A 10-meter long simply supported beam carries a uniform load of 8 kN/m for 6 meters from the left support and a concentrated load of 15 kN 2 meters from the right support. Determine the maximum shear and moment. (A) Vmax = 41.8 kN; Mmax = 92.23 KN-m (B) Vmax = 33.2 kN; Mmax = 85.92 KN-m (C) Vmax = 31.3 kN; Mmax = 81.74 KN-m Vmax = 36.6 kN; Mmax = 83.72 KN-m

Q: Make and draw the shear and moment diagram for the beams shown below. You can give or assign the…

A:

Q: For the beam and loading shown below: a) draw the shear and bending moment diagrams, and b)…

A:

Q: A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall…

A:

Q: at the top to 90 kPa at the bottom. As an additional support, it is anchored at depth y = 2 m. with…

A: cantiliver retaining wall is subjected to a soil pressure linearly varying from zero at the top to…

Q: Q1 Draw the shear-force and bending-moment diagrams for the cantilever beam AB 12 kN/m 4 kN ic B 7…

A: RAx+RBy=4+12×1.6RAx+RBy=23.2 .......(1)Now taking  moment at point A…

Q: The figure shows a cantilever beam carrying a uniformly distributed load of 4 kN/m and a point load…

A: Shear force at any cross-section of the member is equal to the algebraic sum of concentrated point…

Q: For the beam and loading shown, draw the shear and bending moment diagrams. Note: Support A is…

A:

Q: A simply supported beam of width 100 mm, height 200 mm and length 4 m is carrying a uniformly…

A:

Q: Draw the shear and moment diagrams for the beam.

A: Draw the free body diagram of the given member and calculate the reactions: Consider the…

Q: Draue shear, and moment dingrams. Indicate units, line typeo,mberseations, etc. 140 kN 80 kN- m 20…

A:

Q: 211Draw the shear force and bending moment diagrams of the simply supported beam shown in Figure…

A:

Q: Draw shear and bending moment diagrams for the beamin Figure 3.14b, which carries a uniformly…

A: givencantilever beam as shown below

Q: (b) Determine locations where either the internal moment or shear force of the beam is maximum. A…

A: To find: Location of the maximum shear force acting in the beam = ? Location at which internal…

Q: Draw the influence lines for the vertical reaction and the reaction moment at support A and the…

A: Consider the following influential diagram for vertical reaction at A From Muller Breslau’s…

Q: A loaded beam, 60 mm wide by 100 mm high and 6 m long, has the shear and moment diagrams as shown…

A: Given: The width of beam, b = 60 mm = 0.06 m The height of beam, h = 100 mm = 0.1 m The length of…

Q: gomm S.3 20 EN 20EN 30 mm A 3m |30mng b0 mm b. 30 mm 50mm A beam AB, made of three boiled boards, is…

A: Given:

Q: The maximum bending stress

A: Given data; A simply supported beam of , width=100mm=0.1m height=200mm=0.2m length=4m load=10kN/m

Q: For the beam and loading shown, draw the shear and bending moment diagrams. Determine the magnitude…

A: For the beam and loading shown,To Find-Draw the shear and bending moment diagrams.The magnitude of…

Q: 3. Torques are added to the beam at points B and D as shown. T₁ = 5 kip-feet, and T₂ = 2 kip-feet: w…

A:

Q: Draw the normal force (N), shear force (T) and bending moment (M) diagrams of the beam whose span…

A: Sign Convention for SFD 1) Right Upward Negative 2) Right Downward positive 3) Left upward Positive…

Q: (1) Draw the shear force and bending-moment diagrams for the beams shown below. 10 kN 20 kN 15 kN 3…

A:

Q: PROBLEM 4 From the beam shown, determine the internal shear force acting at point C and the maximum…

A: Consider below figure to identify the cut section plane:

Q: A man with his tools having a total weight W = 1.012 kN, steps on the retractable ladder. %3D The…

A: Given data, Total weight, W = 1.012 KN h = 540 mm = 0.54 m l1 = 0.365 m l2 = 0.286 m l3 = 0.761 m To…

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum…

A:

Q: 3 kN/m |6.0 kN 1 kN/m A B 500 mm 0.5 m 000 1.0 m→1.0 m→ 2.0 m- -4.0 m 200 mm

A:

Q: Find the lightest-weight W-flange beam that will support the loading shown. Allowable bending stress…

A: The SFD and BMD of the beam is shown below;

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.