A 10 kg block rest on an inclined plane making an angle of 30 degrees with the horizontal. a. find the ecoeffcient of friction between the block and the plane to keepthe block from sliding b. determine the normal reaction c. determine frictional force

Q: The crate has a weight W=200N and the coefficient of static friction at the surface is µ=0.38. A…

A:

Q: what are the zero force members?

A: A zero force member is a member(a single line segment) in a truss which, given a specific load, is…

Q: Need Help on this one pls.

A:

Q: Question 3 Part a: For the section shown, determine the: • Maximum elastic Moment M Fully plastic…

A: Given Dataσy=250 MN/m2E=200 GN/m2We are supposed to calculate the following parameters.Maximum…

Q: Hi, may i ask how to do these questions?Thank you for helping?

A: Solution for 12.93 Given;P=3kn

Q: 150 mm F = 30N 150 mm water 3m When a 30N force is placed on the end of a floating 150mm x 150mm x…

A:

Q: How Find max. tensile and comporsive -: stresses.

A:

Q: The wooden section of the beam below is reinforced with two steel plates as shown. determine the…

A:

Q: Solve the problem with complete solution in landscape orientation by placing it in a short coupon…

A: To find magnitude of friction force acting on each block

Q: A solid shaft in a rolling mill transmits 20 KW at 2r/s. Determine the diameter of the shaft if the…

A: Given: The power is 20 kW. The frequency is 2 Hz. The maximum shear stress is 40 MPa. The angle of…

Q: The beam with cross-section shown carries a uniformly distributed load of intensity w over its…

A: Given,  There is a two side overhang beam given in the question.  Total length of the beam = 4.5m…

Q: Blocks A and B have masses of 10 kg and 20 kg respectively. The coefficient of static friction…

A: Solution: Given Data MA=10 kgMB=20 kgμ1=0.20μ2=0.10μ3=0.15

Q: The se extra examples are presented by Mohammed Dhayaa 2021@ H.w.l Given v, = 25m/s %3D S.g.= 0.83…

A: Given Data; v1=25 m/s d=50 mm Specific gravity=0.83

Q: 4. Determine whether the following are in tension or compression: AD AB DE 2000 N 1000 N 8m 12 m D 6…

A: Compression Members: Compression members show the compaction or the compression force in the…

Q: The standard length of a tape is 100m having a weight of 2kg with the standard temperature of 20°C…

A:

Q: A hollow circular column of steel (E = 30,000 ksi) is subjected to a compressive load P. The column…

A:

Q: The continuous beam and post system shown below supports a 10 kip vertical load and a 5 kip…

A: The moment and shear force will act at point B. Moment and shear will be caused due to force of 5…

Q: A constant force P is applied to a block over a distance d. (A) (B) m (D) (F) (E) 2v Which case has…

A:

Q: A wood beam 150 mm wide by 300 mm deep is loaded as shown in the figure. If the maximum flexural…

A:

Q: 1. From the given figure below, determine the maximum moment of the beam and compute for the maximum…

A: Let,RA=vertical reaction at support A in upward directionRB=vertical reaction at support B in upward…

Q: Please

A:

Q: R=25 P2-49 50B 258 2-49. The 25-lb force R in Fig. P2-49 is the resultant of four forces, three of…

A: Given a set of four parallel forces and their resultant. The magnitude of three forces is known and…

Q: A tubu being The m.

A: G=4000ksi L=7ft N=1800rpm P=490hp to find Dmin

Q: A 364-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: Given data in question  Load Coefficient of friction  To find out Determine force P

Q: A B 30° 7. Determine the maximum force P that can be applied without moving the two Y-kg crates.…

A: Note:- “Since you have posted multiple questions, we will provide the solution only to the first…

Q: probiem 25 points each 1. The two vertical rods attached to the light rigid bar are identical except…

A: from  deflection triangle ∆A4=∆B8∆B=2∆A         ∆=FLAEFBLBAE=2×FALAAE…

Q: The boiler has an inside diameter of 60.0 in. and a wall thickness of 1.000 in., and it is made of…

A:

Q: A base line was measured with a steel tape of designated length 30 m at 20°C at a pull of 100 N. The…

A:

Q: A 10 kg block rest on an inclined plane mak ing an angle of 30° wi th the horizontal. a. Find the…

A:

Q: A tubular steel strut 2 m long, both ends hinged, must have a buckling load of120 kN, based on the…

A:

Q: Analyze the frame by Substitution Method 400 lb VE 500 Ib 30° 30 D FO 12 ft A C 45° B 6 ft- 6 ft

A:

Q: The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the…

A: Determination of shearing stress on the plane of grain

Q: 17-18. A horizontal steel rod, 3.2 m long and 1200 mm² in cross-sectional area is secured between…

A: Length of steel rod = 3.2 m Area of cross section = 1200 mm2 Rod is stress free at 20oC Temperature…

Q: Show complete solution. Draw the following structures then classify whether Statically Determinate,…

A: Static indeterminacy is a conjecture that shows the difference between the total number of unknowns…

Q: The standard length of a tape is 100m having a weight of 1.2kg with the standard temperature of 20 C…

A: Normal tension occurs when Sag correction is equal to pull correction.

Q: Determine

A:

Q: 1. The blocks shown are connected by flexible, inextensible cords passing over a frictionless…

A:

Q: need a complete and clear solution

A: Column: - It is defined as the structural element which is used to transfer load from top to bottom.

Q: A rectangular beam has a design moment of 40 kNm. The material has a 200 MPa yield strength. Create…

A:

Q: Kindly write complete and clear solutions

A:

Q: A rectangular wooden beam (fb = 5.9 MPa, E = 17.3 GPa) has a cross-sectionalarea of 250 mm by 500…

A:

Q: Design of Beam in Flexure Use Working Stress Method   Fc=10 MPa Fs=120 MPa n=12 Bar Diameter =…

A: