A 10 kg block A is released from rest 2 m above the 5 kg plate P, which can slide freely along the smooth vertical guides BC and DE. Determine the velocity of the block and plate just after impact. The coefficient of restitution between the block and the plate is e =0.75. Also, find the maximum compression of the spring due to impact. The spring has an unstretched length of 600 mm.

A 10 kg block A is released from rest 2 m above the 5 kg plate P, which can slide freely along the smooth vertical guides BC and DE. Determine the velocity of the block and plate just after impact. The coefficient of restitution between the block and the plate is e =0.75. Also, find the maximum compression of the spring due to impact. The spring has an unstretched length of 600 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum normal stress (MPa) in member BC. Let diameter of bar BC be 25 mm. 60 KN K J I ДИМА 3m 3m 3m 3m 3m 3m C D E 80 KN 60 KN L B 40 kN H F 5m
Write your step by step solution.
A solid 0.78-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3). a.)3.86 ksi b.) 3.51 ksi c.) 3.15 ksi d.) 5.38 ksi e.) 4.85 ksi
1.Solve with correct fbd
Q1. A horizontal bar of nagligible weight and assumed rigid is supportad by two rads, AB and CD, and hingad : the right and. Data for the rods are as follows: Rod AB: L= 2 m, A= 1950 mm. E= 80 GPa ; Rod CD: L=2.5 m, A= 1200 mm, E= 200 GPa Ifthe maximum unit stress in AB is not to exceed 90 MPa, and the maximum allowabla load for CDis 110 kN, determine the maximum value of the force F. B F 0.60 m. 1.90 m 1.20 m
The constructed shaft is composed of a tube AB and a solid bar BC. The tube has an inner diameter of 20 mm and an outer diameter of 28 mm. The bar has a diameter of 12 mm. Determine the average normal stress at points D and E and identify whether the points are in compression or tension.answer:σD = -13.26 Mpa (compression) σE = 70.74 Mpa (traction)
Problem # 1: A hollow shaft has an outside diameter 60 mm and a wall thickness of 1.25 mm. The maximum shear stress in the shaft must be limited to 150 MPa. Use G = 43 000 MPa. Determine: (a) the maximum power that can be transmitted by the shaft if the rotation speed must be limited to 20 Hz. (b) the magnitude of the angle of twist in a 700-mm length of the shaft when 30 kW is being transmitted at 8 rpm.
WA 4-m bar of negligible weight rests in a horizontal position on the smooth planes shown in the Figure, if T = 30 KN and x = 1 m. Determine the Reaction at A. 1m P = 20 kN 30° 45° 4 m 16.82 KN None of the above O 44.83 KN O 25.89 KN 36.60 KN
Two smooth cylinders are placed in the position shown. Cylinder A 1,000N and has a radius of 10cm while cylinder B has a radius of 8cm and weighs 750N. Cylinder A is connected by a 35cm string to the smooth wall C. What is the tensile stress in MPa, developed in the string if the diameter of the string is 10mm and angle beta is 25°? Bº ...
Gate AB in the figure is 1.2 m wide and hinged at A and kept closed by a stop at B. Gage G reads 14.86 kPa. Oil has a specific gravity of 0.76. Determine the total hydrostatic force acting on the gate in (kN), Determine the location of the total hydrostatic force from the hinge in (m), Determine the reaction at the stop in (kN)
Refer to the illustration below. ?′?=28 MPa, ??= 400 MPa. Answer all subparts: a. Determine the ultimate axial capacity of the spiral column b. Determine the maximum spiral pitch c. Determine the clear spacing between the main reinforcements
If the reaction of the ballast on the railway tie can be assumed uniformly distributed over the cross-section along the length as shown. Determine the maximum bending stress developed in the tie. The tie rectangular section has a thickness of t = 6 in.