A 10-ft beam, weighing 1240 lb, is to be moved to the left onto the platform. A horizontal force P is applied to the dolly. which is mounted on frictionless wheels. The coefficients of friction between all surfaces are s-0.30 and Uk=0.25, and initially, x=2 ft. The top surface of the dolly is slightly higher than the platform. -10 ft- D 2 ft B Determine the force P required to start moving the beam. (Hint: The beam is supported at A and D) The force P required to start moving the beam is lb.

A 10-ft beam, weighing 1240 lb, is to be moved to the left onto the platform. A horizontal force P is applied to the dolly. which is mounted on frictionless wheels. The coefficients of friction between all surfaces are s-0.30 and Uk=0.25, and initially, x=2 ft. The top surface of the dolly is slightly higher than the platform. -10 ft- D 2 ft B Determine the force P required to start moving the beam. (Hint: The beam is supported at A and D) The force P required to start moving the beam is lb.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel ramp is used by a worker in a factory to move a cardboard box. The box weighs 40 lb with a center of gravity at point G, the force applied by the worker is parallel to the ramp and the coefficient of friction between the box and ramp is μs = μk = 0.3. Determine the value of the normal force N. Determine the force the worker must apply to slide the box up the ramp. Determine the friction force F acting between the ramp and the box if the worker slid the box up the ramp. Determine the force the worker must apply to slide the box down the ramp. Determine the friction force F acting between the ramp and the box if the worker slid the box up the ramp.
Wedges A and B are shown in the figure. Assume the coefficient of friction between A and B is 0.2 and 0.3 for other contact surfaces. Neglecting the weights of the blocks. • Calculate the reaction between A and B Calculate the reaction between B and the floor Determine the minimum value of P that will prevent block B from sliding to the left B 80 degrees 100 N A
Determine the horizontal force P in the figure to start the 400-lb wedge (a). moving to the right and (b). moving to the left. The angle of friction is 20° at all contact surfaces.
The 50 N homogeneous bar AB is suspended from a rope that runs over a small peg at C. The bar is kept in the position shown by the horizontal force P. Determine the smallest coefficient of static friction at C for which the bar will be at rest.
is 125 lb. The The weight of block A in Fig. weights of the lever and cylinder can be neglected, and the pin at D is frictionless. If the coefficient of friction is 0.50 at B and 0.30 for all other surfaces, determine the force P re- quired to cause impending motion of block A to the left. 50 Ib 5 in. 10 in. 3 in.
The uniform 14-ft pole weighs 150 lb. and is supported as shown. Calculate the magnitude of the force P required to move the pole if the coefficient of static friction for each contact location is 0.40. Express your answer in units of lb. 6' A 14' - יך B - P
A 150-lb block rests on a horizontal floor. The coefficient of friction between the block and the floor is 0.30. A pull of 40 lb, acting upward at an angle of 30° to the horizontal, is applied to the block. Determine whether or not the block will slide. - Draw Free-body diagram - Solve most simple way - use the formula Fmax= Ms (N)
Two identical wood blocks with weight W are being pushed apart by a wedge. The coefficient of static friction for all surfaces is 0.325. Determine the weight of the wedge, P, required to start the blocks moving. The wedge is symmetrical about the vertical, and 0 = 24°. Use the triangle method or the component method. urgenttt thank you
The 250 lb uniform crate (center of gravity at G) shown in the figure must be moved without tipping. The applied force P is horizontal. 1.5 ft 1.5 ft Determine: a. The largest coefficient of static friction between the crate and the floor that allows the crate to slide and 2.5 ft P. not tip 4.5 ft b. The corresponding magnitude of P 3.5 ft Include all needed FBD's to solve, and put units on your answers.
Block A weighing 60 lb rests on block B weighing 80 lb. Block A is restrained from moving by a horizontal rope tied to the wall at C. What force P parallel to the plane inclined 30 degrees with the horizontal is necessary to start B down the plane? Assume coefficient of friction for all surfaces to be 1/3. Give solution. (Ans. P = 40.3 lb)
Calculate the horizontal force P on the light 15° wedge necessary to initiate movement of the 59-kg cylinder. The coefficient of static friction for both pairs of contacting surfaces is 0.39. Also determine the friction force Fg at point B. (Caution: Check carefully your assumption of where slipping occurs.) Answers: P= i 596 FB=366 59 kg B N N