A 1.5m long column has a circular cross-section of 50 mm diameter. Consider 1 Rankine's formula with values of f. = 560 N/mm², 1600 for pinned ends and factor of safety of 3. If one end of the column is fixed and the other end is free, what is the safe load. α =

Q: Problem #2. The steel rod is stress-free before the axial loads P₁ = 150 kN and P₂ = 90 kN are…

A:

Q: An angle member (L-section) is used as a beam. Note that the thickness for the flange and the web is…

A: Given Data: The value of M is, M=50 kN·m The angle from the horizontal is. θ=30° The value of SN is,…

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: A tapered rod with length c = 7m and cross - sectional dimensions a = 270n mm and b = 119 mm is…

A: Asked: To determine the elongation of the given tapered rod.   Given: Length of the rod (c) = 7 m…

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: DETERMINE REACTION AT D

A:

Q: 1 2 Add your answer Ꮎ ] Ꮎ 3 P A system of three bars with similar cross-section and material…

A:

Q: A cantilever beam BD rests on a simple beam AC as shown below. Both beams are of the same material…

A: It can be solved using solving for moments along both the axis.

Q: An 9m long steel column is pinned at the top and fixed at the bottom. The column is provided with…

A:

Q: Problem 4: to The rubber tube (G= 1 MPa) is fixed at both ends and is turned by a rod. Define the…

A:

Q: Let P = 191 N, Q = 198 N, a = 2.5 m, and b = 5.0 m. Type the unit, N, after typing your numerical…

A: Determine the force in member EI. Lets solve using method of joints.

Q: A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the…

A:

Q: The cross-sectional dimensions of a beam are shown. The internal bending moment about the z…

A:

Q: 4. A vertical shaft DA is attached vertically to a fixed base at A and is subjected to the torques…

A: Given: Segment AB - hollow segmentL = 600 mm, Inner diameter = 44 mmSegment BCL = 200 mm, Diameter =…

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa , a1=a2=…

A:

Q: A = 2000 mm² A = 900 mm² B 503 mm 257 mm 355 mm The steel rod is stress-free before the axial loads…

A:

Q: A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor…

A:

Q: Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a…

A: Determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2).…

Q: Problem 1 A beam spans 7 m and its cross section is rectangular. The beam supports its own self-…

A:

Q: A beam is supported by single journal bearings at both ends. A distributed load defined by the…

A: Given : Wx = 5x2-7x+19 lb/ft d1=0.5 ft d2=7 ft

Q: The two bars shown in the figure are used to support a load P. When unloaded, joint B has…

A:

Q: Derive the expression

A: Expression for change in length of the block

Q: statically determinate truss.

A: External force at point A in x direction is P1 = 50KN External force at point A in y direction is P2…

Q: A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three…

A:

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A:

Q: y F = 25 kN P = 75 kN 6 cm. 4.8 cm 2.4 cm 3.6 cm 4 cm 10 cm

A:

Q: The frame is subjected to distributed load of 500 kN/m as shown in the figure. Analyse the response…

A: E = 2.05e8  # Young's modulus in kN/m2I = 5.54e-4  # Moment of inertia in m4A = 0.012  #…

Q: A simply supported wooden I beam AB (shown below) is loaded by the distributed force q = 1.9 kN/m.…

A: Given data:

Q: MA

A:

Q: Note: Please show all of the free body diagrams used (from reactions and etc.,) and also show the…

A:

Q: All Elements have a fixed value of E and I. Do load modelling for 1 meter strip width in the water…

A:

Q: 1.20 The hoisting rope for a mine shaft is to lift a cage of weight W. The rope is of variable…

A: The problem is based on stress and equilibrium concepts.  Let the cross section at height z be Az…

Q: A = 900 lbs 25° 75⁰ B = 600 lbs

A:

Q: If A = 75°, C = 37° and b = 6, work out the length of a. %3D %3D B a C [C

A: Given data:  A=75∘C=37∘b=6

Q: Consider the beam shown in (Figure 1). Take P = 2 kip and w = 1.9 kip/ft. Point E is just to the…

A: A beam is roller supported at A and fixed at C, also an internal hinge is present at B.At the…

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.