A 1-m³ rigid tank with air at 1 MPa and 400 K is connected to an air line. The valve is opened and air flows into the tank until the pressure reaches 5 MPa, at which point the valve is closed and the temperature inside is 450 K. 16. Determine the initial mass in the tank 8.71 kg 0.00871 kg 0.04355 kg 43.55 kg 38.71 kg 7.743 kg 17. Determine the final mass in the tank a. b. C. d. e. f. a. b. C. d. 43.55 kg 38.71 kg 7.743 kg 18. The tank eventually cools to room temperature, 300 K. What is the pressure inside the tank then? 4.4 MPa 3.3 MPa 3.75 MPa e. f. 8.71 kg 0.00871 kg 0.04355 kg a. b. C. d. 750 kPa e. 667 kPa f. 889 kPa

A 1-m³ rigid tank with air at 1 MPa and 400 K is connected to an air line. The valve is opened and air flows into the tank until the pressure reaches 5 MPa, at which point the valve is closed and the temperature inside is 450 K. 16. Determine the initial mass in the tank 8.71 kg 0.00871 kg 0.04355 kg 43.55 kg 38.71 kg 7.743 kg 17. Determine the final mass in the tank a. b. C. d. e. f. a. b. C. d. 43.55 kg 38.71 kg 7.743 kg 18. The tank eventually cools to room temperature, 300 K. What is the pressure inside the tank then? 4.4 MPa 3.3 MPa 3.75 MPa e. f. 8.71 kg 0.00871 kg 0.04355 kg a. b. C. d. 750 kPa e. 667 kPa f. 889 kPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
What’s the correct answer for this please?
I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal places for magnitude. DO NOT FORGET YOUR UNITS. Enclose all final answers in a box. No need to copy the question or problem. File submissions should be a single PDF. II. PROBLEM SOLVING 1) Given the figures and data below, solve what is being asked for. Y-axis 200mm -200mm 50mm 50mm 100mm 200mm 100mm Y-axis Yo 200mm 100mm 3°1 100mm 547 - ATT HA LO - CHIR →→X-axis -Xo →X-axis
Round off the numbers in the following problems to three significant figures. Find the percent difference between each rounded-off number and the original number by using the original number as the reference. 6748.3
You are given a metal rod, cut to a length of 12 in plus/minus .25in. Then you need to cut off 2 in with an accuracy of plus/minus .25 tolerance. You end up with a 10 in rod but what is the tolerance? (hint: rely on the basic principle of tolerance
What’s the correct answer for this please ?
Don't answer if you already answered this. If i see the same solutions, i'll downvote you. Follow the instructions. Typewritten for upvote. No upvote for handwritten. Thank you
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
Round off the numbers in the following problems to three significant figures. Find the percent difference between each rounded-off number and the original number by using the original number as the reference. 26.394
Please only answer number 8
Name Lab Activity 5J Calculating Points on a Mill Part Use the illustration provided to calculate points on a mill part. 3.000 XO.YO. .500 R.50 2 .500 1 6.000 3 5.000+0.001 1. What are the X and Y coordinates of point number 1? X: Yi Date 2. What are the X and Y coordinates of point number 2? X X₁ FLICT Class -.375 X 45 2.000±0.001 3. What are the X and Y coordinates to the center of radius at point number 3? X X- Y+ Y- - X+ Goodheart-Willcox Publisher
Please answer from iv onwards as you have already sent me the answer to the other please show working and correct answer