A 02-series single-row deep-groove ball bearing is to be selected from Table 11–2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr= 8 kN, axial load Fa=3 kN, design life LD = 10°, ring rotation factor V= 1.2, and reliability RD= 0.95. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Assuming that the values taken from Table 11.1 are X= 0.56 and Y= 1.63, determine the equivalent radial load rating for this application. The equivalent radial load rating for this application is kN.

A 02-series single-row deep-groove ball bearing is to be selected from Table 11–2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr= 8 kN, axial load Fa=3 kN, design life LD = 10°, ring rotation factor V= 1.2, and reliability RD= 0.95. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Assuming that the values taken from Table 11.1 are X= 0.56 and Y= 1.63, determine the equivalent radial load rating for this application. The equivalent radial load rating for this application is kN.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Being a Mechanical Engineer, you are asked to design/select a deep groove ball bearing of bore diameter of 2cm for an axial load of 1000 lbs and radial load of 500 lbs. Desired life is 200x106. Consider both load application factor and reliability factor 1.
An 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?
Select an angular contact ball bearing to carry a radial load of 336lb at a shaft speed of 1800 rpm for 5500 hours. Anapplicationfactorof1.2isappropriate. Use a reliability of 96%.
A ball bearing is subjected to a radial load of 2000 Nat 880 rpm for 40% of the time and to a radial load of 1000 Nat 1760 rpm for the remainder of the time. Expected life is to be 10 years at 6 hours per day. Find the minimum value of the basic rating load C that the bearing must have. Loads are steady. (it is assumed that the bearing has but one row of balls. A working year will be taken as 250 days.) Ans. C = 15,160 N
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
Pravinbhai
2) A shaft is designed with two 6305 bearings. At bearing 1, the radial load is 20 lb, and at Bearing 2, the radial load is 40 lb. What is the expected life of EACH bearing assuming a reliability of 97%? What is the reliability for BOTH bearings together?
Kindly answer correctly. Please show all the necessary steps. Thanks in advance
A Self-aligning medium series bearing for bores of 85 mm is operating at 300 r.p.m for an average life of 9 years at 10 hours per day, is acted by a 15 kN radial load and 10 kN thrust load. The bearing is subjected to a light shock load and the inner ring is sationary. Determine the suitable self-aligning bearing. Mention the advantage of using self align bearing.
A joint is subject to a cyclic loading. There is an acceptable preload of 1,200 lbs, and the axial load is fully reversed with an amplitude of 1,600 lb. THe tensile bolt area is 0.160 in^2. Ignore any design factors and (take all nd=1) and assume the loads include the 1.2 bolt factor. If the joint constant is 0.25, the alternate and means axial stress for the bolt are: a) sa = 1,250 psi sm = 0 b) sa = 1,250 psi sm = 8,750 psi c) sa = 2,500 psi sm = 0 d) sa = 2,500 psi sm = 7,500 psi