Solve correctly stepwise solution plz. A 0.464Show answer choicesB0.5370.245Assume the camber lineis a circular arcD) 0.42438°E 0.319C2038°40°With the figure provided in one of the problems (not in order), what is the local diffusion factor? (Hint: use the equivalent diffusionratio)25 mm52°35 mm52°60⁰75 m/s

To find: The local diffusion factor.

A 0.464 how answer choices B 0.537 0.245 Assume the camber line is a circular arc 0.424 38° 0.319 C2 38° 40° 25 mm With the figure provided in one of the problems (not in order), what is the local diffusion factor? (Hint: use the equivalent diffusi atio) 52° 35 mm 520 60° 75 m/s

A 0.464 how answer choices B 0.537 0.245 Assume the camber line is a circular arc 0.424 38° 0.319 C2 38° 40° 25 mm With the figure provided in one of the problems (not in order), what is the local diffusion factor? (Hint: use the equivalent diffusi atio) 52° 35 mm 520 60° 75 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
2. FR1: Allow control of water flow rate FR2: Allow control of water temperature Develop the design matrix, A, for both design options and comment on the designs. Hot 0₁ I Cold I 0₁₂
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
A marine engine cylinder has a compression ratio (r) of 9.5, a clearance volume of 650 cm3and a piston stroke length of 675 mm. What is the bore diameter in millimetres (mm) for the engine cylinder. Give your answer to the nearest millimetre mm.
Please solve only 3 and 4
Find the gradient of a crawler tractor pulling a loaded rubber tire skimmer using the following information: The horsepower of the tractor is (180) horsepower. . Tractor weight (20.25) tons. The traction force of the crawler tractor in the first gear is (15300) kg. The weight of the loaded skimmer is (39.48) tons . The dirt road is not good. Rolling resistance of the tractor (73) kg / ton. The rolling resistance of the skimmer is (95) kg/ton.
solve 30-40 minutes hand written asap..i'll rate
Solve for Fv
Problem 1. Simplify the following expressions (note that 8, is the Kronecker delta, repeated index means summation, and comma represents derivative). (a) Sim Smp Sap (b) ▼ Skmum,n (c) ▼ x 8kmui,mk
Problem #3 - Modeling, Mixing Problem Two tanks are connected by pipes in parallel as shown in Figure 2. Tank 1 starts with 160 lb of salt dissolved in 200 gal of water. Tank 2 starts with 100 gal of pure water. Using the diagram below, solve for the particular solutions of salt concentration in each tank as a function of time. Plot the solutions in Excel on the same plot. Note: some flow rates have been intentionally left out of the diagram below; use the conservation of mass to determine those. As a thought experiment, consider what negative eigenvalues imply. What would it mean if the eigenvalues were positive instead (what would the math say)? i.) ii.) iii.) iv.) v.) vi.) vii.) Use a conservation equation to develop your differential equation model (you should end up with two ODEs to describe the change in salt in both tanks). Write your system of ODEs in matrix form. Set up the eigenvalue problem and then determine the eigenvalues. Use the eigenvalues to determine the…
Find the greatest and smallest values of the velocity ratio of two shafts joined with a universal coupling when the axes are at 60o to each other. Produce a graph of velocity ratio against angle for f to proof the calculated results.
HCM-6 At the design speed Vo Dan's car can go around a banked curve of radius 150M and banking angle of 10.0° without any friction force. The car is shown as viewed from behind in the figure below. R=150m 10.0° a) Use the figure above to draw the free body diagram for the car. Also show on the FBD the direction of the car's acceleration and show coordinate axis directions. b) Write down newtons's second law in component form for the car. Use NO numbers for this part. c) Use your equations from step b) to find the design speed Vo.