A 0.360-m-long metal bar is pulled to the left by an applied force F. The bar rides on parallel metal rails connected through a 45.0- Ω resistor so the apparatus makes a complete circuit. You can ignore the resistance of the bar and rails. The circuit is in a uniform 0.650-T magnetic field that is directed out of the plane of the figure. At the instant when the bar is moving to the left at?

A 0.360-m-long metal bar is pulled to the left by an applied force F. The bar rides on parallel metal rails connected through a 45.0- Ω resistor so the apparatus makes a complete circuit. You can ignore the resistance of the bar and rails. The circuit is in a uniform 0.650-T magnetic field that is directed out of the plane of the figure. At the instant when the bar is moving to the left at?

Similar questions

A 1.0 m long metallic rod is rotated with an angular frequency of 400 rad s1 about an axis normal to the rod passing through its one end. The other end of the rod is in contact with a circular metallic ring. A constant and uniform magnetic field of .5 T parallel to the axis exists everywhere. Calculate the emf developed between the centre and the ring.
No Battery: A metal rod is dragged along two parallel rails in a uniform 0.36 T magnetic field, as shown in the figure below. The rails and the field extend for a total distance of 1.53 m. A voltmeter connects the two rails, which are 12 cm apart. V X X X X X X X X X The rod is dragged to the right at a constant speed of 3.00 m/s. What will the voltmeter register as the rod passes the halfway point? (A positive voltage indicates a clockwise current.)
The figure below shows a top view of a bar that can slide on two frictionless rails. The resistor is R = 6.2002, and a 2.50-T magnetic field is directed perpendicularly downward, into the page. Let = 1.20 m. xxxxxx x xxxxxx xxxxxx xxxxxx xxx x xxxxxx xxxxxx x x x x x x x xxx app (a) Calculate the applied force required to move the bar to the right at a constant speed of 1.90 m/s. 3.338709 XN (to the right) (b) At what rate is energy delivered to the resistor? 7.679 XW
A square loop,10.0cm on a side, is placed aroundthe center of a long solenoid which has 1500 turns of wire per meter. Thediameter of the solenoid is 9.00cm. The square coil has a resistance of 8.00. A cross section of the setup is shown toright. a.Determine the magnitude and the direction of the magnetic field inside the solenoid if it has a current of I=5.00 Amps in the direction shown. b.The initialcurrent through the solenoid is zero, at t =0 the current in the solenoid begins increasing according to the formulaI(t)=C1t2whereC1=5.00Amp/s2. Determine the magnitudeanddirectionof the current in the square coil at a time of .600 seconds.
A circular coil with radius 0.564 m has 50 turns of wire in it. The total resistance of the coil is R and it is sitting in a perpendicular magnetic field of 10 T. As the magnetic field is ramped to zero over a period of 2 s, a 5.0 A current is induced in the coil. What is R? Hig Ο 10 Ω 15 Ω 30 Ω
A helicopter (see figure below) has blades of length 2.80 m; extending out from a central hub and rotating at 3.40 rev/s. If the vertical component of the Earth's magnetic field is 50.0 μT, what is the magnitude of emf induced between the blade tip and the center hub? mV Sascha Hahn/Shutterstock.com
A circular piece of wire with radius 0.89 m has a 84.9 T magnetic field passing through. What is the maximum magnetic flux that can pass through this ring?
what is the answer??! help!
A 20 turn circular loop with diameter 3 cm is placed in a magnetic field of strength 7 T such that the loop’s area vector is parallel to the magnetic field. The magnetic field is reduced to 0 T over some time and this generates a constant voltage of 5 V. How long did it take for the magnetic field to reduce to 0? 3.23 s 15.32 s 0.0198 s 0.0389 s None of the above
A 2 meter-long bar is being moved to the right at a constant speed. The bar is sliding on aframe that includes a resistor with R = 3.25 Ω. There is also a uniform 5.75-T magneticfield, directed into the page. At what speed should the bar be moved to produce a currentof 0.800 A in the resistor
A 0.25 m long solenoid contains 104loops of wire. What current will be necessary to produce a 0.5 T magnetic field inside the solenoid?
The magnetic field inside an air-filled solenoid 37 cm long and 2.1 cm in diameter is 0.75 T. Approximately how much energy is stored in this field?