A 0.30-kg ball is attached at the end of a 0.90-m-long stick. The ball and stick rotate in a horizontal circle. Because of air resistance, a continual push must be exerted on the stick to keep the ball moving at a constant speed, causing a 0.036-Nm torque. Draw an extended force diagram showing the forces exerted on the ball and stick and use it to determine the magnitude of the resistive force that the air exerts on the ball opposite its motion. What assumptions did you make?

A 0.30-kg ball is attached at the end of a 0.90-m-long stick. The ball and stick rotate in a horizontal circle. Because of air resistance, a continual push must be exerted on the stick to keep the ball moving at a constant speed, causing a 0.036-Nm torque. Draw an extended force diagram showing the forces exerted on the ball and stick and use it to determine the magnitude of the resistive force that the air exerts on the ball opposite its motion. What assumptions did you make?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A rotating door is made from four rectangular glass panes, as shown in the figure. The mass of each pane is 94.8 kg. A person pushes on the outer edge of one pane with a force of F = 71.7 N that is directed perpendicular to the pane. Determine the magnitude of the door's angular acceleration. 1.2 m 1.2 m Number i Units
On a playground, there is a merry-go-round. In order to get it moving, Bonnie applies a force of 17 N. The merry-go-round measures 5.3 m from the axis of rotation to the edge where Bonnie applies her force. Assuming she applies her force perpendicularly to a line drawn from the axis of rotation, what is the magnitude of the torque t Bonnie imparts to the merry-go-round? T = N.m
Just need part B
Consider the setup shown below. The blocks have masses 3.6 kg and 24 kg. The pulley has mass 7.4 kg, and is a uniform disc with radius 0.23 m. Assume the pulley to be fric- tionless, but the coefficient of friction between the block and the surface is 0.36. a T2 3.6 kg T1 = 0.36 22° 24 kg What is the acceleration of the blocks? As- sume the 24 kg mass is descending with accel- erațion a. The moment of inertia of the disk is - M R? and the acceleration of gravity is 2 9.8 m/s?. Answer in units of m/s?.
+, F. You use a wrench to turn a rusty nut. You place your hand at where the black dot is and apply a force F = 110N at an angle 0 = 59 degrees. The distance from your hand to the center of nut d = 30 cm. Calculate the torque in N. m your hand applies. %3D %3D %3D p. 0. MacBook Pro G Search or type URL
To remove a nut from an old rusty bolts, you apply a 100 neutron force to the end of a wrench at a 45° angle to the wrench handle. The distance from the applied force to the axis of the bolt is 25 cm. what is the torque exerted on the bolt and N.m
A coke can is suspended by a string from the tab so that it spins with a vertical axis. A 14 N perpendicular force at the edge causes rotation. Find the angular acceleration if the can has a radius of 4 cm and a mass of 427 grams.
You are installing a new spark plug in your car, and the manual specifies that it be tightened to a torque that has a magnitude of 55N·m. Using the data in the figure, determine the magnitude F of the force that you must exert on the wrench.
A group of physics students, each of whom can pull with 100lb of force, is planning to topple a 9600lb statue that the school built for the meanest teacher. Assume the statue does not slide.Answer all questions relative to the rotation point. How much torque is caused by the statue's weight? How much tension must the students generate to "barely balance" the statue? What is the minimum number of students (whole number) needed to topple the statue?