A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft. 43.33 MPa 35.01 MPa 13.12 MPa 22.11 MPa

A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft. 43.33 MPa 35.01 MPa 13.12 MPa 22.11 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 32 mm 60 mm bo 30 mm 24 mm 15 mm 180 mm 750 N 40 mm 500 N P 16 mm

A: To a cantilever beam, loading is given To determine normal and shear stress at points a, b, and c…

Q: For the beam shown: 1. Draw the free-body diagram (FBD) and determine the reactions at the supports.…

Q: Determine the shear stress (in Mpa) in the 30.97-mm-diameter pin at B that support the beam if P =…

Q: 2. Compute the SUPPORT REACTIONS of the loaded beam shown. Use consistent deformation method. 20 KN…

Q: Determine the average normal stress and average shear stress at point C in the beam. The…

Q: A compound shaft consists of an outside tube (1) and an inner tube (2) that are fully connected…

Q: 200 mm 3 m 20 mm - 20 mm w, kN/m 1 m 200 mm 1 m 3 m R2 R1 20 mm 100 mm

Q: In figure shown, P = 10 kN, a = 250 mm, b = 150 mm, and e = 60°. If the average shear stress in the…

A: Free body diagram

Q: The steel pipe is supported on the base plate as shown in fig (5).if the t=50mm and d=300mm…

A: Using formula to find bearing stress

Q: Problem 1. The shaft is subjected to the axial force of 50kN. 1. Determine the normal stress in the…

Q: If the average normal stress in each of the 20-mm diameter bars is not allowed to exceed 150 MPa,…

A: To determine the maximum value of force P, such that the average normal stress in the bars does not…

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings and axial load…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A 2.5 m long and 30 mm thick tie bar is of tapered section. The longitudinal section tapers from a…

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250…

Q: 1 Determine the required thickness of member BC and the diameter of the pins at A and B to the…

Q: 13) Diameter of the solid shaft AB is 130 mm. Determine the maximum shear stress in the solid shaft…

A: Given- TA=10Kn-mTB=10Kn-md=130mmThe magnitude of TorqueAB is TAB=10 Kn-m

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm and a…

Q: The rigid pipe is supported by a pin at C and steel guy wire AB 10 mm in diameter E = 200 GPa and v…

Q: 8. Compute the total deformation of bar ABC with a uniform thickness of 15 mm. Use E = 30 GPa. 20 mm…

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 214 mm and a…

Q: Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of…

A: Method of Consistent Deformation : The method of consistent deformation is also known as force…

Q: Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A: Given Normal stress 175 MPaShear stress 75 MPaAngle 45Diameters 6 mm and 10 mmTo find out Maximum…

Q: Q.7.20 In a stressed member wo strain gauges are fixed such that they are inclined at 30° to the…

Q: PLS ANSWER ASAP Use Method of Consistent of Consistent Deformation to solve the horizontal reaction…

A: Consistent Deformation Method : The consistent deformation method is also known as force method of…

Q: thickness of the wall of the hollow segment is 15 mm. B 4 kN-m CITY

A: To find the maximum shear stress-

Q: A simply-supported beam with length, L = 7 m, is carrying a downward uniform load, w = 34 kN/m…

A: Answer We are given Beam span L = 7 m uniform load w = 34 Kn/m We know that flexural shear stresses…

Q: antilever hollow circular bar 5 mm thim ide diameter of 75 mm is subjecte ue of 3 kN.m at its free…

Q: Using method of consistent deformation, determine the vertical reaction at C (in kN). Indicate only…

Q: A hollow shaft with an outside diameter of 150 mm and an inside diameter of 130 mm is subjected to…

Q: If M=50 kN-m, what is the bending stress at the center of the upper hollow circle about the z-axis?…

Q: The beam is supported by two rods AB and CD that have cross-sectional areas of 7mm² and 15mm²,…

Q: The shaft below is fixed at D. A hole with a diameter of 44-mm has been drilled into portion CD of…

A: Given that : Diameter of hole = 44 mm G = 77 GPa A) Angle of twist of end A with respect to end D…

Q: A compound shaft drives several pulleys, as shown. Segments (1) and (2) of the compound shaft are…

A: Given data Modulus of rigidity Length Diameter Solid and hollow tubes Torques

Q: For the overhang beam shown, determine the shearing stress (a) at the neutral axis and (b) at the…

A: Left support is considered as A and Right support considered as B

Concept explainers

Planar Stresses

Question

100%

A 0.2 m diameter shaft is supported by a smooth journal bearing at E and a smooth thrust bearing at F. Determine the maximum shear stress developed in segment BC of the shaft.

43.33 MPa

35.01 MPa

13.12 MPa

22.11 MPa

A B
D
E
F
20 kN-m
35 kN-m
85 kN-m
30 kN-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design the beam using IPE shape.
For the structure shown, determine the following: a. The normal and shear stresses in section b. The maximum normal stress in member BC (ksi) c. The maximum bearing stress on member AB (ksi) Pins A & C have a diameter of 34 in while pin B has a diameter of %2 in. Both members have a thickness of 0.4 in. There are two support plates at A. 1.5 in. B 60° 8 ft (ksi) 2 kip/ft A O Adapted from Hibbeler's Mechanics of Materials (10th ed.)
if the shaft is subjected to ana axial force of 5 kN. determine the bearing stress acting on the collar A. Determine the average shear stress developed on the shear plane on collar A
Current Attempt in Progress The horizontal shaft with a diameter of d- 43 mm is supported by a thrust collar that rests on a 29-mm-thick plate. The thrust collar is 20-mm thick. The thrust collar has an outer diameter of Dcollar - 63 mm. Determine the load P that causes an average shear stress of 69 MPa on the cylindrical surface of contact between the shaft and the thrust collar. Thrust collar area Plate d Thrust collar Dcollar Answer: P- kN
Cross-section of each member is 400 mm2 2 m 19. Determine the normal stress at 2 m member GI. 20. Determine the normal stress at F15m--15m-15m---15m- member BC. 21. Determine the 6KN normal stress at member CJ. 22. Determine the normal stress at member DE.
8.47 Three forces are applied to 100 mm diameter plate that is attached to the solid 46 mm diameter shaft AB. At point H, determine (a) the principal stresses and principal planes, (b) the maximum shearing stress. 27 kN 50 mm 50 mm 27 kN 11 kN 200 mm
= For the section shown, if a = 15 mm, b 30 mm, h = 120 mm, 1 = 7646787 mm^4 and M = 30 kN.m, then the bending stress at the bottom of the hole is b hole h a 218.6 MPa zero -75.63 MPa O 75.63 MPa -218.6 MPa
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
Cross-section of 160 KN the members are 40 mm s0 kN diameter. 60 kN 6 m For the given 4. truss, calculate the normal stress at member AB. 5. Calculate the normal stress at member BC. 6. Calculate the normal stress at member DE. Calculate the normal stress at member EG. 7.
3.75 pts For the shown figure, member BC has a square cross section and the applied load P at point Cis 45 kN. Find 5 kN/m the length of the cross-section side that is required to ensure that the developed shear stress at section a-a is D not allowed to exceed 120 MPa. AB = 4 m, AD = 2 m, AC =3 m. o 11.772 mm O 6.697 mm O 15.546 mm B. O 10.828 mm Next
using method of consistent deformation, determine the vertical reaction at C (in kN). Indicate only the magnitude. Use E= 200 GPa and I=5x10^7 mm4
Determine the maximum normal stress (in Mpa) in bar ABCD if the cross-sectional area of the bar is A = 566 mm2 and P = 37.65 kN. 25 KN 20 KN B. 1.5 m- 3 m C 3 m D P