_1. What is a type of tool that used to loosen or tighten screws that have a star-like depression on the top, a feature that is mainly found on a laptop? b. Philip Head Screwdriver c. Torx screwdriver a. Multimeter 2. What is the type of tool used to tighten and loosen slotted screws? a. Flat-head screw driver b. Needle Nose Pliers c. Tweezers 3. What is the type of tools used in used to prevent ESD damage to computer equipment? a. Anti-static Mat b. Anti-static wrist strap c. Lint-free cloth

_1. What is a type of tool that used to loosen or tighten screws that have a star-like depression on the top, a feature that is mainly found on a laptop? b. Philip Head Screwdriver c. Torx screwdriver a. Multimeter 2. What is the type of tool used to tighten and loosen slotted screws? a. Flat-head screw driver b. Needle Nose Pliers c. Tweezers 3. What is the type of tools used in used to prevent ESD damage to computer equipment? a. Anti-static Mat b. Anti-static wrist strap c. Lint-free cloth

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the two forms of abrasives used in benchwork?
12 2X 011 40 25- 12 08 v 014.5X 62 12 R10 20 30 35 7 D 25 12 105 026 15- 07 V012X 829 58 Ø12 AD R12 Ø3 THRU 25 R12 09 L015 18 28 18 18- 25 120 SECTION A-A SECTION B-B SECTION C-C Ø12 V 20 U018 65 3X 012.5 20- R15 T 8 R12 25 20
The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True False
Detail information of machine tool can be found Oa. Research articles b. Online Databases OC. User manual d. Catalogues
the tool is hacksaw... you should ignore if you can't grrrr
11. With aid of neat sketches, explain the drilling parameters. 12. With aid of neat sketch, explain the main parts of the twist drill cutting tool. 13. With aid of neat sketch, explain the point angle of the twist drill. 14. With aid of neat sketch, explain what is the difference between the counter boring and counter sinking. 15. Define “NC" and "CNC" Terms.
5
In ______________the tools are lowered into the well by a cable. The obtained data are transmitted to the surface recording system via the cable to the surface for further investigation purpose. a. Wire line logging b. Vertical drilling c. Coring d. Sideway drilling e. Horizontal drilling
Disposal Instruction of CNC lathe machine Below is the example of answer that i needed
21. How to hold the hammer handle whlie driving the nail? a.Middle of the handle. bi. Anywhere in length of the handle. C. Near the hammer head of the handle. d. End of the handle USF ال لجنة العلمية 22. The angle of single cut file is- a. 65°. b. 70°. c. 75°. d. 80°. 23. The most accurate manufacturing process is: a. Sand casting b. Forming. Rolling. d. Machining. C. 24. Avoid using compressed air to clean chips from the milling machine because. it does the job too slowly. b. flying chips may cause eye injuries. C. it gives a poor finish to the job. d. it is too expensive. 25. Before operating a lathe machine, you should a. remove all safety guards. b. oil the area surrounding the machine. C. wear rings and jewellery. d. make sure you know the location of the ON and OFF switch. 26. Which of the tool used for testing the straightness of large surface?: a. Da
Hydraulic drive is considered heavy duty and provide a smooth and strong movement within the machine tool design. Analyze the diagram of figure 1 below and answer the questions. Operative element Hydraultc cylinder Rocking lever Direction- control vatve -Throttle Pressure valve - Gear pump Figure 1: Translatory Hydraulic Drive a) From your analysis, which of the component that is controlling the pressure delivered to the hydraulic cylinder? b) By the analysis of figure 1 above, compare the speed of the extend and retract of the hydraulic cylinder above. c) Define the function of the rocker arm in the figure.
Multiple grooving is most suited for: a/Rough grooving when the depth is bigger than the width b/Minimizing vibrations and radial forces c/ Machining steel and stainless steel and when the width of the groove is larger than the depth