the weight ww is 60.9 N.What is the tension in the diagonal string?Find the magnitudes of the horizontal forces F→1 and F→2 that must be applied to hold the system in the position shown. 90.0°90.0°F₁45.0°W90.0°F2

Answered: Image /qna-images/answer/a977c9ea-7237-4de3-a862-1eb6d0d11246.jpg

Answered: 90.0° 90.0° F₁ 45.0° W 90.0° F2

Science

Physics

90.0° 90.0° F₁ 45.0° W 90.0° F2

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A student gets his car stuck in a snow drift. Not at a loss, having studied physics, he attaches one end of a stout rope to the vehide and the other end to the trunk of a nearby tree, allowing for a small amount of slack. The student then exerts a force F on the center of the rope in the direction perpendicular to the car-tree line, as shown in the figure below. If the rope is inextensible and if the magnitude of the applied force is 504 N, what is the force on the car? (Assume equilibrium conditions.) KN 12 m Tree 0.50 m
PROBLEM 3. Rod XY and smooth surface O hold the 1600-N cylinder in equilibrium as shown. Find the force Q exerted by the rod and the normal force N exerted by the smooth surface on the cylinder. Ignore the weight of the rod XY. SUMMARY OF ANSWERS Q 25
Please asap
Consider the 120-cm board supporting three loads as shown below. The beam weighs 45 grams. If the system is in equilibrium, a. what is the magnitude of the force exerted by the pin support to the board? b. Find the perpendicular distance, x, of the pin support from the left end of the board. 30cm A В C 259 30g 75g
A rigid vertical rod of mass 75 kg and length 4.0 m is connected to the floor by a bolt through its lower end A. The rod also has a wire connected between its top end B and the floor as shown in the figure. A horizontal force F = 500 N is applied at the midpoint of the rod. What is the tension in the wire?
Three construction workers wish to remove a pole from the ground. They tie ropes to the pole and pull horizontally on the ropes. The diagram represents the forces exerted on the pole. 110 N 76 N 35° 40° 55 N Pole P a) Determine the direction (as measured with the x-axis) in which the pole will move. b) What must be the magnitude and direction of the equilibrant force needed to keep the pole in equilibrium?
A cylinder C rests on a horizontal surface. A small particle of mass m is held in equilibrium connected to an overhanging string as shown. The other end of the mass less string is being pulled horizontally by a force F as shown. Find F. F A
Structural member AB is to be supported by a strut CD. Determine the smallest length CD may have, and specify where D must be located for a strut of this length to be used. Take x= 120 mm. 60 mm D. y 20 mm E The smallest length CD may have is mm. The coordinates of point Dare ( and Imm.
Figure shows the two cables AO and BO tied together at O and the loadings are also shown. A В 30° 30° (a) Derive the expressions relating the tension in each cable as a function of a. 150N 200N (b) Write a MATLAB program to plot the tension in each cable for 0° < a < 90°. (c) Determine the value of a for which both cables OA and OB are in tension.
An archer's bow is drawn at its midpoint until the tension in the string is 0.866 times the force exerted by the archer. What is the angle between the two halves of the string? Number i ! Units ° (degrees)
O Problem As shown below, a 246 N horizontal beam is in equilibrium. The orange circle represents the hinge and the 6.5 m long cable has a tension of 766 N. 6.5 m Determine the weight of the hanging mass as well as the magnitude & direction of the force that the hinge exerts on the beam. hanging mass weight 8.755 N x hinge force magnitude = 2.5 m hinge force direction = relative to the horizontal.
O Each diagram in Figure 12.20 shows the magnitude and direction of the forces acting on an object. Find the resultant force in component form in each case. F, F. F, F10 F, Figure 12.20