9.40 The circuit shown in Fig. P9.40 is operating in the sinu- PSPICE soidal steady state. The capacitor is adjusted until the MULTISIM current i, is in phase with the sinusoidal voltage vg. a) Specify the capacitance in microfarads if vg = 80 cos 5000r V. b) Give the steady-state expression for ig when C has the value found in (a). Figure P9.40 800 mH 10 k2

Q: 4. Name 3 methods how drawings are stored in?

A: Any single paper object or book would appear to be straightforward to keep and preserve on its own.…

Q: How does one determine the coordinating time between a protective device and a downstream device?…

A: The protective devices should be subjected to minimum overcurrent in minimum time to accomplish…

Q: Q1) A) What is bus? How many ways to construct bus system. (explain with example for one type)

A:

Q: How does IoT fit into the concept of the "smart grid" in energy distribution

A: We need to explain How  IoT fit into the concept of the smart grid in energy distribution.

Q: Make an essay about Kirchoff's Law (Voltage and Current Law). Include its definition, uses,…

A: KIRCHOFF'S VOLTAGE LAW: The sum of voltage difference in each branch in any closed loop must be…

Q: Vab=C --- ) v (a) 2.5 v (b) - 2.5 v (c) - 10 v (d) 10 V

A: The solution can be achieved as follows.

Q: help please answer in text form with proper workings and explanation for each and every part and…

A: Digital comparators are used in:CPUs and ALUs for arithmetic and logic operations.Digital Signal…

Q: Grateful a little help with this homework thanks.

A:

Q: What is the difference between “MicroStation”, “InRoads”, “Geopak”, MX, and “Open Roads” software?.

A: To describe the difference between different software solutions like Microstation, Geopak, MX, and…

Q: what was the calculation done to get d? Confused on how this was rearranged.

A:

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: With neat diagram explain the construction and working principle of strain gauge

A:

Q: Choose 1.Moving equipment or parts is the hazard associated with what energy source?…

A: The solution is given below

Q: uestlon No. 10 Explain why K-Maps are used. Explain all possible groupings that can be done in K-…

A:

Q: Q2)  The certain operational amplifier has the following data sheet specifications: IOS= 0.80 µA and…

A:

Q: is it possible you can work in multi-sim?

A: Given, We need to implement it in multisim.

Q: How to turn-off a voltage source? A) Set it to zero. B Replace it with a short-circuit. C) You can't…

A: This is a basic problem of circuit. The solution is given in the next step.

Q: What is switch Debouncing ? List two correct this problem. or more ways.

A:

Q: Fill in the blank: Electrical hazard boots are made up of highly materials.

A: Electrical Hazard boots are used to prevent the shock

Q: 5. Define protective device coordination. Why it is important in electrical power systems?

A: coordination describes the design of an electrical system in which the upstream protective devices…

Q: what type of lenses for Myopia and Hypermetropia? explain and draw. Option 1

A:

Q: Q1) Fill in the blanks by inserting appropriate words/numbers 1- The low value of k in voltage…

A:

Q: Mark the correct statement Select one: O a. Insulators are those materials that contain electrons…

A: The resistance of a material is directly proportional to the length of the material and inversely…

Q: What information needs to be provided for the introduction to “EFFECT OF VEGETATION ON V2V…

A:

Q: What does a compatible load mean? What if the load is not compatible?

A: This question is from "Power system and protection". Under which we are going to study load…

Q: 4. Which of the following can't be included in data required for coordination study? a) X/R Ratio b)…

A: as per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: 4. What is PPE?

A: here we have to find the what is PPE.

Q: Where push-buttons are being used in our daily lives? State some examples.

A: Given: Push button

Q: 1. Name three (3) sensors that robots can use?

A: Given :    Note :  According to the guidelines of the company we supposed to answer the first…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: 4- Can you trigger the TRAIC in (Q1 or Qıv), explain briefly?

A: Semiconductor are the material made of pure Si or Ge or compound . They have conductivity in between…

Q: Define and differentiate accidents, unsafe acts and unsafe conditions. essay at least 30 words

A: Electrical Hazards: Hazards are always there with Electricity. it causes damage to equipment on…

Q: Write-down any 4 power system problems solving by the static Var controls.

A: In present lots of problems are there in distribution and transmission networks.In ac networks…

Coulomb’s Law

Coulomb's law states that the attraction or repulsion force between two charged things is proportional to the product of their charges and inversely proportional to the square of their distance. It has an effect along the line that connects the two-point charges.