9.27 Determine the average power absorbed by the 4-k2resistor in Fig. P9.27.vs(t) = 2 cos wt V2 kNvo(t) 3 4 kN1 kNFigure P9.27++1

Given that, VS(t)=2 cos (ωt) VR1=2 KΩR2=1 KΩROUT=4KΩ Put the given voltage in phasor form VS=2∠00 V

Answered: 9.27 Determine the average power…

Engineering

Electrical Engineering

9.27 Determine the average power absorbed by the 4-kN resistor in Fig. P9.27. vs(t) = 2 cos wt V 2 kN vo(t) 3 4 kN

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: help please answer in text form with proper workings and explanation for each and every part and…

A: I solved the problem.

Q: The effective value of the sinusoidal voltage across a certain network is 32 V rms and the peak…

A: Given data, Ip = 24 mA. Vrms = 32 V. P = 0.48 W.

Q: 9. The instantaneous values of two alternating voltages are given as: v1=60sine and v2=40sin(0 -…

A: Solution !! Horizontal component of v1 = 40VVertical component of v1=0VHorizontal component of…

Q: An alternator is supplying a load of 300 kW at a p.f. of 0.6 lagging. If the p.f. is raised to…

A: Given, An alternator is supplying a load of, P1 = 300 kW At power factor, cosϕ1=0.6 lagging Raised…

Q: E9.21 Find the value of capacity to be connected in parallel with the load in Fig. E9.21 to make the…

A: Given circuit is shown below:

Q: Determine the power and the rms value of: (a) 8(t) = C cos (wot + 0) (b) g(t) = C1 cos (wit +01) +…

A: The standard form of sinusoids are given hence the power will be the square of the RMS value of the…

Q: A load consumes 44 kW at 0.82 pf lagging from a 22020° V rms, 60-Hz line. A capacitors of 900 μF is…

A: I have written this solution as handwritten solution. Hope you find the perfect solution.

Q: For the circuit shown below, the complex power absorbed by the element (5+j10 ohms) is VA 5Ω 120/0°…

Q: An inductive load operates from a 140 V, 60HZ supply and is rated 2.25 kW @ p.f. .707 lagging. What…

Q: A lighting load operates from a 208V, 60Hz supply and is rated 1 kW @ p.f. .707 lagging. What size…

A: The reactive power demand when the capacitor is not connected is, Substitute the values.

Q: Given the network shown determine the input voltage phasor Vs in rms units using complex power if…

A: The complex power in an AC system is defined as the product of rms value of applied voltage and…

Q: An alternator is supplying a load of 300 kW at 0.6 p.f. lagging. If the power factor is raised to…

Q: The power consumed in an ac circuit is given by a. Vm Im b. (Vm Im/2)cosO c. IZcose d. Vm Im cose

A: According to the question we have to discuss the power consumed in the ac circuit.

Q: Question No.64 An industrial consumer has a load pattern of 2000 kW at 0.8 lagging for 12 hours and…

A: Given data: An industrial consumer has a load pattern of, Power demand, P1=2000 kW at 0.8 lagging…

Q: Find the value of Z, in Fig. P9.35 for maximum average power transfer to the load. 20 -j4 N= j2 n…

A: The circuit is given as, The expression for the thevenin impedance is given as,…

Q: The average Powet to the Plant Shown in Fig is 2479 KW and Powey factor is 0.707 with W=377 tad/sec…

A: Given Real power of plant(Pp)=2479 KWPower factor of plant(cos∅1)=0.707 lagω=377 radsecEffective…

Q: (a) Find the effective value of the voltage waveform shown below. Rms vclve v(t) 10 5n 0 2 4 6 8 10…

Q: 9.51 Calculate the rms value of the waveform shown in Fig. P9.51. v(t) (V) A 4 0 012 Figure P9.51 no…

Q: wo electric devices A and B are connected in parallel, and the rms current in A is 15 amp. If the…

A: It is given that: IL=23.3 AIA=15 A

Q: The voltage between the ends of a load and the current through it are given by: v (t) = 20 + 60…

Q: The 2430 KW average power the plant sShown in fig to and the Power factor is o lo1 logging. The…

Q: O9.3.10 Determine the impedance Z, for maximum average power transfer and the value of the maximum…

Q: Calculate the average power transferred by the source in the circuit given below. 2 H 50 cos5t 1 H :…

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: An AC voltage source of 100V and 50HZ is supplying a coil that has an inductance of 180 mH in series…

Q: A load with a voltage amplitude of 50 Hz 300 V rms at its terminals consumes 28.98 kW at a back…

A: Given Data:The circuit for the given description will be of,To Find:Decreased amplitude of the…

Q: An alternator is supplying a load of 350 kW at a p.f of 0.7 lagging. If the C3 raised to unity, how…

A: In this question active power with power factor given..We have to find new active power with given…

Q: The avetoge Power to the Plant Shown in Fig is 2479 KW and Power factor Is 0.707 logging The…

Q: Determine the real and reactive power supplied by the source vs(t) 15 cos(5t) V. The real and…

Q: E9.21 Find the value of capacity to be connected in parallel with the load in Fig. E9.21 to make the…

A: It is given that:

Q: The avg power to the plant Shown in fig in 2430 KW o 107 lagging. The and the power factor genorador…

Q: Examples When connected to a 120-V (rms), 60-Hz power line, a load absorbs 4 kW at a lagging power…

Q: Find the average power absorbed by the resistor R R = 40 N %3D 2.5 N 1:2 50/0° V (rms) R Ideal O a.…

A: The solution is given below

Q: A building with inductive loads has an average consumption of 40kW and 26 kVAR. What is the average…

Q: An industrial load connected to a 440 V, 60 Hz line takes 50 A. The current lags the voltage by 30…

A: Given:- Voltage (V)=440 V Frequency (f)=60 Hz Current (A)=50 A Current lags the voltage by 30…

Q: A typical SME food factory 37 kW capacity and for continuous use and 27 kW for food processing…

A: We need calculate plant factor, we know direct formula for plant factor.

Q: A load consumes 44 kW at 0.82 pf lagging from a 22020° V rms, 60-Hz line. A capacitors of 1683 μF is…

A: The active power consumed by the load, The power factor, The supply frequency, The supply voltage,

Q: In the circuit of Fig. P. 9.5.4 if the load is 2 kW, 230 V heater and V₂ = 230 V, 50 Hz. Calculate:…

Q: 17 If i(t) = 0.5 cos 2000t A, find the average power absorbed b each element in the circuit in Fig.…

Q: 10/0°v( + j1 Ω -j1 Ω 1ΩΣ 2/30° A

A: Circuit is given as:

Q: If the RMS phasor voltage accross an element is: Vrms = 304 1 • Volts and the RMS current flowing…

Q: Determine the power delivered (in W) by the AC voltage source in the circuit below? The AC voltage…

A: It is given that:

Q: マL-- E9.8 Find Z for maximum average power transfer and the maximum average power transferred to the…

Q: What is the speed of an inductor motor of 7 poles if the slip is 2.1%

Q: The power company supplies 80 kW to an industrial load. The load draws 220 A rms from the…

A: Explanation: The power supplied from the power company = 80 kW Load current I = 220 A (rms) Load…

Q: (a) An industrial load consumes 44 kW at 0.82 pf lagging from a 240/0° -V rms 60 Hz line. A bank of…

A: In this question we need to find the new power factor of the total load when the capacitor is…

Q: E9.19 Find the power factor of the source and vs(t) in Fig. E9.19 if f = 60 Hz. j0.4 Ω Figure E9.19…

A: Given: f=60 Hz. Required: Power factor of the source and vst.

Question

100%

9.27 Determine the average power absorbed by the 4-k2
resistor in Fig. P9.27.
vs(t) = 2 cos wt V
2 kN
vo(t) 3 4 kN
1 kN
Figure P9.27
+
+1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Derive the formula for Average Power, Pavg = VI cosθ watts, where V is the root-mean-square (rms) voltage in volts, I is the root-mean-square (rms) current in ampere, and cosθ is the power factor. For the derivation, use the sinusoidal voltage and current equations. The angle between the voltge and current is angle θ
Determine the power and the rms value of: (a) 8(t) = C cos (wot + 0) (b) g(t) = C1 cos (wt + 01) + C2 cos(@zt + 02) (c) wi 7 w2 8(t) = Dejaot
Pen paper solution please
What is the average power per sq. meter that can be produced by a tidal current of 1.5 m per second? Take the sea water density as 1,220 kgm-3. Select one: O A. 4.11 MW O B. 2.01 MW O C. 411.7 kW
slove it for me pls
Ggg
1. A plant draws 250 A rms from a 240-V rms line to supply a load with 50kW. What is the power factor of the load?
E) An industrial plant operates under the following conditions: the load is 60 kW, the line voltage is 220/0° Vrms at 60 Hz, and the power factor is 0.7 lagging. If 2500 µF of capacitance is placed in parallel with the load, determine the new power factor. Ans. .968 lagging. (What if the load is given in VA instead of W)
Give: A circuit with a voltage (in V) across its terminals and a current (in mA) through as follows • v(t) = 4 + 12 cos(377t + 60')-6 cos(754t – 30°) • i(t) = 5 + 10cos (377t + 45°) + 2 cos (754t + 15°) entering from positive terminal Find: • The average power consumed by the circuit • The AC power fraction in (%)
of food that you cannot afford to let spoil. You would days. The freezer in the basement contains $300 worth also like to keep one window air conditioner running, as well as run the refrigerator in your kitchen. When these appliances are on, they draw the following currents (all values are rms): Air conditioner: 9.6 A rms @ 120 V rms pf = 0.90 lagging Freezer: 4.2 A rms @ 120 V rms pf = 0.87 lagging Refrigerator: 3.5 A rms @ 120 V rms pf = 0.80 lagging In the worst-case scenario, how much power must an emergency generator supply?
7. In the OPAMP circuit shown in Fig. 7, Vs = 10230° V. Find the average power absorbed by 20kΩ resistor. Assume the OPAMP to be ideal. V₁ Μ ell www 10 kΩ 2 ΚΩ j4 ΚΩ Fig. 7 m j6kΩ 20 ΚΩ -j12 ΚΩ
A plant consumes 120 kW at a power factor of 0.707 lagging from a 480 V, 60 Hz supply line. Determine the value of the capacitor that, when connected in parallel with the load, will raise the power to 0.95 lagging. A 624 μ F O + Vs 10 I Plant Inductive: load IL ...