9.17 For the die casting shown in Figure P9-17, determine the maximum stresses and their locations.Let E = 30 × 106 psi and v= 0.25. The dimensions are shown in the figure.V=Figure P9-17.1.0625 in.-1.625 in.0.625 in.Fixed edge1.2 in.2.5 in.-7.05 in.Axis of symmetry0.5-in. radius30°-0.75 in.0.125-in.radius62°4.175 in.0.1875 in.P = 10,000 lb0.4375 in.

It is asked to find the maximum stress and locations

Answered: 9.17 For the die casting shown in…

9.17 For the die casting shown in Figure P9-17, determine the maximum stresses and their locations. Let E = 30 x 106 psi and v=0.25. The dimensions are shown in the figure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

20 the rollers - see later Rolling pressure, P = Y x [1+ua/h] UNIVERSITY OF LIVERPOOL Calculate the average rolling pressure required to reduce 3mm steel sheet by 1mm in rollers with 200mm diameter, if the sheet yield stress Y=200 MPa and μ-0.3 --001
15.28 For the fixture shown in Figure P15-28, the inside surfaces of the eight holes are increased in temperature by 80 °F. Determine the von Mises stresses throughout the fixture. What is the largest von Mises stress in the fixture? Is there concern for fail- ure due to yielding of the material? Assume the material is aluminum alloy 6061-0 (annealed). Fix the inside surface of the upper hole. 60.60 0.30 R 0,60 Y tax Lx $0.50 Figure P15-28 0.25 R மத் 0.10 0.40 (All dimensions in inch units) 0.50 in. R chamfer typ. 500 R 150 0.625 1.500 625- 0.775 -2.50 -0.30 3.00 0.60 dia. -0.60 dia. -0.150 R (All holes 0.60 in. dia. (6) with 0.50 in. rad. chamfer)
(a) Figure 1.1 shows a thick cylinder with inside radius of r;=94 mm and outside radius ro =136 mm was pressurized internally Pi = 56 MPa and externally Po= 26 MPa. Analyse: i. The hoop stress and radial stress on internal and external surface of the cylinder. ii. The hoop stress and radial stress at r= 115 mm. iii. The maximum and minimum shearing stress. iv. Sketch the distribution of hoop stress and radial stress along the cylinder wall. Po Figure 1.1 The thick cylinder
Problem 5: (D2) You are an engineering intem at a manufacturer of mechanical tools, your senior engineer asked you to evaluate the stresses on a newly-design brass eye-bolt, shown in Figure.7, to confim it's not exceeding its yield strength. The bolt dimensions are (d, R) = (8, 12) mm. The task can be completed by calculating the stresses at the inner and outer surfaces of section B – B. located at an angle of 40° from the positive x-axis, when the load is F = 0.4 kN. R FA B
use abaqus to solve this
Example 4.5 (Stress on a shrunk fit cylinder): A shrunk fit thick cylinder made of steel having an inner radius 8cm, interface radius 10 cm and outer radius 12 cm is subjected to an external pressure of -0.09M Pa. Internal pres- sure is atmospheric. Given that the shrinkage is 0.02 cm. Determine the radial and tangential stress distribution across the the thickness of the cylin- der (2) before loading with pressure and (b) after loading with pressure. The equation for the contact pressure with usual notations is given as AE(c² – a²)(b² – c²) Pc = 2c°(b² – a²) Take E = 200 x 106 kPa.
Prove the formula for Hoop stress and longitudinal stress and also explain poisson ratio.
Solve please with correct answer
I need answer within 20 minutes please please with my best wishes
Solve it pls.
ans b please
Given: Flat rolled sheets are produced in wide rolling mills, but many products are manufactured from strip stock. The below figure is a free-body diagram of a shaft for a short slitting line where a single blade is placed in the center of the shaft and a motor drives the shaft through a pulley at the far right end. Find: The shaft diameter If the maximum shear stress is 40 MPa and the largest gage sheet causes a blade force of 2000 N,