9.15 A high-speed flywheel in a motor is spinning at 500 rpm when a power failure suddenly occurs. The flywheel has mass 40.0 kg and diameter 75.0 cm. The power is off for 30.0 s, and during this time the flywheel slows due to friction in its axle bearings. During the time the power is off, the flywheel makes 200 complete revolu- tions. (a) At what rate is the flywheel spinning when the power comes back on? (b) How long after the beginning of the power failure would it have taken the flywheel to stop if the power had not come back on, and how many revolutions would the wheel have made during this time? ●●

9.15 A high-speed flywheel in a motor is spinning at 500 rpm when a power failure suddenly occurs. The flywheel has mass 40.0 kg and diameter 75.0 cm. The power is off for 30.0 s, and during this time the flywheel slows due to friction in its axle bearings. During the time the power is off, the flywheel makes 200 complete revolu- tions. (a) At what rate is the flywheel spinning when the power comes back on? (b) How long after the beginning of the power failure would it have taken the flywheel to stop if the power had not come back on, and how many revolutions would the wheel have made during this time? ●●

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure, wheel A of radiusrA = 13.9 cm is coupled by belt B to wheel C of radius rc = 24.4 cm. The angular speed of wheel A is increased from rest at a constant rate of 1.45 rad/s². Find the time needed for wheel C to reach an angular speed of 50.5 rev/min, assuming the belt does not slip. (Hint: If the belt does not slip, the linear speeds at the two rims must be equal.) Number i Units
The flywheel of a steam engine runs with a constant angular velocity of 132 rev/min. When steam is shut off, the friction of the bearings and of the air stops the wheel in 1.40 h. (a) What is the constant angular acceleration, in revolutions per minute-squared, of the wheel during the slowdown? (b) How many revolutions does the wheel make before stopping? (c) At the instant the flywheel is turning at 66.0 rev/min, what is the tangential component of the linear acceleration of a flywheel particle that is 42.7 cm from the axis of rotation? (d) What is the magnitude of the net linear acceleration of the particle in (c)?
In the figure, two 7.60 kg blocks are connected by a massless string over a pulley of radius 1.30 cm and rotational inertia 7.40 x 104 kg-m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 1.20 rad in 154 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T, and (d) string tension T? Assume free-fall acceleration to be equal to 9.81 m/s?.
A circular disc with radius r = 0.81 m rotates around its own axis. How far has the disk rolled after the time 8,241 s if the disk starts from rest and the angular acceleration is α (t) = k x t^n rad/s^2, where k = 3.48 and n = 1.8?
A flywheel witha diameter of 1.30 m is rotating at an angular speed of 253 rev/min. (a) What is the angular speed of the flywheel in radians per second? (b) What is the linear speed of a point on the rim of the flywheel? (c) What constant angular acceleration (in revolutions per minute-squared) will increase the wheel's angular speed to 994 rev/min in 63.7 s? (d) How many revolutions does the wheel make during that 63.7 s? (a) Number i Units (b) Number i Units (c) Number i Units (d) Number Units
9.16 A flywheel in a motor is spinning at 570.0 rpm when a power failure suddenly occurs. The flywheel has mass 40.0 kg and diameter 75.0 cm. The power is off for 33.0 ss, and during this time the flywheel slows down uniformly due to friction in its axle bearings. During the time the power is off, the flywheel makes 220.0 complete revolutions. At what rate is the flywheel spinning when the power comes back on? Express your answer in revolutions per minutes.
A turntable 46.0 cm in diameter diameter starts from rest, and rotates at 68.0 rpm at its first complete revoļution with constant angular acceleration. If it maintains the same acceleration, a) what is the rotational speed at time 34.0 seconds? b) what is the tangential speed of a point 10 cm from the edge of the turntable at time 34.0 seconds? Enter answer "O" in the answer box. Submit in the corresponding folder (or email) your solution by 3:50 pm, include a sketch/drawing of the rotating wheel, and a step- by-step solution.
In the figure, a solid cylinder of radius 5.5 cm and mass 14 kg starts from rest and rolls without slipping a distance L = 6.9 m down a roof that is inclined at angle = 39°. (a) What is the angular speed of the cylinder about its center as it leaves the roof? (b) The roof's edge is at height H = 5.2 m. How far horizontally from the roof's edge does the cylinder hit the level ground? (a) Number (b) Number i Units Units H
In the figure, two 5.70 kg blocks are connected by a massless string over a pulley of radius 140 cm and rotational inertia 7.40 x 104 kg-m². The string does not slip on the pulley: it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 1.20 rad in 126 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T, and (d) string tension T;? Assume free-fall acceleration to be equal to 9.81 ms?. (a) Number Units (b) Number Units (c) Number Units (d) Number Units >
A metal disc with 0.18 kg of mass and 0.070 m of radius rolled without slipping on a horizontal floor. A ramp was placed on the floor. The disc rolled up the incline without slipping to a vertical height of 0.43 m before stopping. The ramp has a length of 1.7 m along the incline. Find the speed of the disc before it reached the ramp. Hint: the disc has rotational kinetic energy. The rotational inertia of a disc is (1/2)mr^2.
In the figure, two 6.30 kg blocks are connected by a massless string over a pulley of radius 1.30 cm and rotational inertia 7.40 x 104 kg-m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 0.800 rad in 126 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T,, and (d) string tension T,? Assume free-fall acceleration to be equal to 9.81 m/s. (a) Number Units (b) Number Units (c) Number Units (d) Number Units
Please Asap