9.1 (A). Determine the hoop and longitudinal stresses set up in a thin boiler shell of circular cross-section, 5m long and of 1.3 m internal diameter when the internal pressure reaches a value of 2.4 bar (240 kN/m). What will then be its change in diameter? The wall thickness of the boiler is 25 mm. E = 210 GN/m; v = 0.3. [6.24, 3.12 MN/m²; 0.033 mm.]

9.1 (A). Determine the hoop and longitudinal stresses set up in a thin boiler shell of circular cross-section, 5m long and of 1.3 m internal diameter when the internal pressure reaches a value of 2.4 bar (240 kN/m). What will then be its change in diameter? The wall thickness of the boiler is 25 mm. E = 210 GN/m; v = 0.3. [6.24, 3.12 MN/m²; 0.033 mm.]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
The pressure tank shown is fabricated from 1/8-in steelplate. Calculate the allowable internal pressure if thecircumferential and longitudinal stresses are limited to20 ksi and 10 ksi, respectively.Answer: p= ___________________
A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall thickness of 10 mm. The tank is pressurized to 2.40 MPa. Determine the hoop stress in the wall of the tank.
A steel pipe with an outside diameter of 115 mm and an inside diameter of 105 mm supports the loadings shown. Assume a = 510 mm, b = 230 mm, P = 20 kN, P, = 16 kN, and P; = 11 kN. (a) Determine the normal and shear stresses on the top surface of the pipe at point H. (b)Determine the principal stresses and maximum in-plane shear stress magnitude at point H and show the orientation of these stresses on an appropriate sketch. a P: P H K
The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum longitudinal stress caused by an internal pressure of 1.2MPA if the steel plate has a thickness of 10mm. b. Determine the maximum circumferential stress caused by an internal pressure of 1.2MPA, if the stress plate has a thickness of 10mm. c. Determine the minimum thickness plate which maybe used if the stress is limited to 40MPA and the internal pressure is 1.5MPA. 1400 mm 400 mm 600 mm
Solve it
4. A boiler 6ft. in diameter with ½inch plate has 70% longitudinal efficiency. If the allowable stress is 10,000psi, find the allowable internal pressure in Pa. А. 1.029 х 106 В. 1.342 х 106 С. 1.4344 х 106 D. 0.67 x 106
Please full solution with the drawing. Big and clear handwriting
A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which has an outside diameter of 40mm and an inside diameter of 30mm. The length of the brass tube exceeds that of the round steel bar by 0.12mm. Rigid plates are placed on the ends of the tube through which an axial compressive force is applied to the compound bar. Determine the compressive stresses in the bar and tube due to force of 60 kN. Use 200 GPa for modulus of elasticity of steel and 90 GPa for modulus of elasticity of brass.
Question 1 A stainless-steel thick-walled cylinder with inner and outer radii (b and a) of 225 mm and 350 mm, respectively, is designed to contain steam at a pressure of 120 MPa. Determine the maximum shear stresses induced in the inner, middle and outer surfaces the vessel wall by this pressure.
Question 3 - Strain Energy A brass tube with an outside diameter of 20 mm and 4 mm wall thickness is 80 mm long.It is joined to the end of a solid brass rod with a diameter of 20 mm and 120 mm long toform a compound assembly. This assembly is subjected to tension due to a mass of 150kg moving at a speed of 0.4 m/s.3.1. Determine the stresses induced in the rod and the tube respectively.3.2. Determine the change in length of each part, as well as the total change in length ofthe assembly.3.3 Determine the equivalent impact load (in kg) required to have the same effect(produce the same amount of energy) if falls freely from a height of 10 cm onto acollar attached to the bottom of the assembly if the assembly is vertically attachedat its top.3.4 How much strain energy is absorbed by each section of the assembly?(For brass: E = 100 GPa and α = 18×10-6/ 0C)
A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of circumferential (hoop) stress to the longitudinal stress is