9. The system shown in Figure 1545 is used to determine lo 10 the coefficient of restitution. If ball A is released from rest and ball B swing through the 0 = 53.1° after being struck, determine e. 8 WA = 30lb (B WB= 2016

Q: 5. To create and emphasize minute details of a carved masterpiece, how will the chisel be oriented?

A:

Q: (d) In one production line, there is ultrasonic machines (USM) and electro- discharge machines…

A: USM stands for Ultrasonic Machining USM is a mechanical energy based non-traditional machining…

Q: How can we analyze the effects of impact?

A: The impact loads are the loads that act for a minimal amount of time but cause severe stresses and…

Q: This is what I drew out. I'm unsure of hidden lines

A: Please refer the completed orthographic views of the given object. The drawing is made with the true…

Q: What is the definition of post-treatment, what they are used for?

A: Post-process, as known by the name, is a process that is usually carried out before any operation it…

Q: Explain the difference between recovery and recycling as applied to solid industrial. 'please send…

A: Industrial waste:  The waste generate in industrial processes or during manufacturing of any object…

Q: ives of drying

A: Preservation of foods and increasing and improving their shelf life by reducing the water content is…

Q: Specify mechanical energy processes from non-traditional machining and which process is suitable for…

A: In an unconventional machining process, some  form of energy such as mechanical energy, electrical…

Q: Explain the performance criteria involved in dryer design

A: A dryer uses sublimation or evaporation to remove moisture or liquids from continuous sheets,…

Q: Can you help me please I really need help? Thank you Explain in your own words how the load…

A: The goal of performance testing is to evaluate the whole system's performance and collect metrics…

Q: methods in m

A: introduction: Metal fabrication firms, despite having a plethora of machinery and techniques at…

Q: Your die setter brings you a compact that has cracks that are at 45 degrees to the horizontal. What…

A: Given data:  Cracks that are at 45 degrees to the horizontal. To be explained:-What caused these…

Q: Given a 6.5 x 2.5 x 1.5 cm solid block of wood and a bandsaw with miter sled (see image below),…

A: GIVEN DATA solid block = 6.5*2.5*1.5 blade thickness = 0.25 cm initial block (figure 1) final result…

Q: Figure 4 shows a HSS drill bit to be coated with TIN coating using either PVD or CVD coating…

A: Requirment    HSS drill bit to be coated with TiN coating using either PVD or CVD coating process.…

Q: A mould has downsprue whose length is 20 cm and the cross sectional area at the base of the…

A: Length of the sprue, h=20 cm or 0.2 mCross sectional area at the base of the downsprue, A=1 cm² or…

Q: epeat the above exercise for basic sheet metal working operations.

A: Sheet metal working process is discussed below

Q: Explain how casing design problems depend heavily on stress analysis techniques, roc nechanics and…

A:

Q: Describe how curves and surfaces are transformed. while discussing computer-generated art,

A: A curve is a collection of points that is indefinitely big. Aside from endpoints, every point has…

Q: There are two common manufacturing processes that create long metal parts with a constant…

A:

Q: Explain the stages for selection of materials for a Ball mill?

A:

Q: Explain process in which there is continuous supply of molten metal available, with a neat diagram…

A: continuous casting is the process, where we use a continuous supply of molten metal. In this…

Q: A moterial is crushed in a Gyratory crusher such that the averoge size of particle is reduced from…

A:

Q: Hi, can you help by explaining Part D above?

A:

Q: Which equation will yield a direct solution to problems involving force,velocity and time?

A: Newton’s second law of motion           It mathematically states the cause and effect relationship…

Q: Explain the importance of lubrication in wire drawing

A: Wire drawing Wire drawing is the process in which metal is pulled out through die using tensile…

Q: Explain in your own words how the stress test (performance test) is applied to the patient turning…

A: Medical equipment to find test performance

Q: There are two common manufacturing processes that create long metal parts with a constant…

A: Extrusion and the wire drawing are the two operation that are used to create long parts with…

Q: 1- Explain why a casting may have to be subjected to various heat treatments. 2- Describe the…

A: Given questions are related to manufacturing engineering and material science. Why a casting may…

Q: Describe the principles from power input of the shaping machine to the output of the tool

A: The shaper machine or shaping machine is that variety of metal cutting tool which is used to remove…

Q: Draw a sound conclusion based on how you familiarized the key components of the shaper machine.…

A:

Q: cup of internal diameter 80 mm and height 45 mm is to be drawn from a sheet metal 2 mm thick. Four…

A: Given:Internal diameter of cup, d=80 mmheight of cup, h=45 mmThickness of sheet metal, t=2 mm

Q: 1. In the manufacture of automotive-body panels from carbon-steel sheet, stretcher strains (Lueders…

A: Given question : How can stretcher strains be eliminated? How wrinkles in deep drawing operation can…

Q: Solid modeling is a technique utilised by designers to enhance the three-dimensional and organic…

A: This question is based on the concept of solid modeling.