## Question 9: Ideal Mechanical Advantage of a Wheelbarrow**Calculate the ideal mechanical advantage of a wheelbarrow where the length of the whole wheelbarrow is 1.8 m and the length to the center of the wheelbarrow basket is 0.6 m.****Options:**- 1- 2.4- 0.5- 3**Explanation:**The ideal mechanical advantage (IMA) of a wheelbarrow can be determined using the formula:\[ \text{IMA} = \frac{\text{Length of handle}}{\text{Length to the center of the load (fulcrum to load distance)}} \]Substitute the given values:\[ \text{IMA} = \frac{1.8 \text{ m}}{0.6 \text{ m}} = 3 \]Therefore, the ideal mechanical advantage of this wheelbarrow is 3.**Correct Answer:** - 3

Given:The length of the whole wheelbarrow = 1.8mThe length of effort arm length = 1.8m-0.6m=1.2…

Answered: 9. Calculate the ideal mechanical…

9. Calculate the ideal mechanical advantage of a wheelbarrow where the length of the whole wheelbarrow is 1.8 m and the length to the center of the wheelbarrow basket is 0.6 m. 01 2.4 0.5 3

Glencoe Physics: Principles and Problems, Student Edition

1st Edition

ISBN:9780078807213

Author:Paul W. Zitzewitz

Publisher:Paul W. Zitzewitz

Chapter10: Work, Energy And Machines

Section10.2: Machines

Problem 28PP

See similar textbooks

Similar questions

Scissors are like a double-lever "Stem, Which of the Simple machines in Figure 9.23 and Figure 9.24 is most analogous to scissors? Figure 9.23 A nail puller is a lever with a large mechanical advantage. The external forces on the nail puller are represented by solid arrows. The force that the nail puller applies to the nail ( Fo ) is not a force on the nail puller. The reaction force the nail exerts back on the puller ( Fn ) is an external force and is equal and opposite to Fo. The perpendicular lever arms of the input and output forces are li and l0 Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
An object moves halfway around a cricle of radius R. A tangential force of magnitude F is exerted on x by y. The work done on the object by the tangential force is a) zero b)FR c) FÀR d
Question 4: Energy Analysis + N2L+ Kinematics: Sliding off a dome A person of mass m initially sits at the top of a hemispherical ice dome of radius R as shown. Upon a slight nudge, the person starts sliding down the ice dome without friction. The nudge is so small that the person has zero speed initially at the top of the dome. a. What is the angular position (with respect to the vertical) for the point at which the person loses contact with the dome? b. If R = 30 m, how far from the edge of the dome does the person land on the ground? R R Ꮎ
A person opens a door by applying a 13-N force perpendicular to it at a distance 0.90 m from the hinges. The door is pushed wide open (to 120 ° ) in 2.6 s How much work was done? Express your answer using two significant figures. να ΑΣφ J Submit Request Answer Part B What was the average power delivered? Express your answer using two significant figures. Hνα ΑΣφ
Use the definition of the vector product and the definitions of the unit vectors i, j, and k to prove Equations 11.7. You may assume the x axis points to the right, the y axis up, and the z axis horizontally toward you (not away from you). This choice is said to make the coordinate system a right-handed system.
A uniform disk of mass 500 kg and radius 0.25 m is mounted on frictionless bearings so it can rotate freely around a vertical axis through its center (see the following figure). A cord is wrapped around the rim fo the disk and pulled with a force of 10 N. (a) How much work has the force done at the instant the disk has completed three revolutions, starting from rest? (b) Determine the torque due to the force, then calculate the work done by this torque at the instant the disk has completed three revolutions? (c) What is the angular velocity at the instant? (d) What is the power output of the force at that instant?
Mechanical principles
28. Jack & Jill went up the hill to fetch a pail of water. At the well, Jill used a force of 20.0 N to turn the crank handle of radius 0.400 m to rotate the axle of radius 0.100 m, so she could raise the 60.0 N bucket of water. What is the efficiency of the wheel? a. 50% b.75% c.100% d.150%
A small box with a mass of 8.00 kg is being swung around on the end of a string which has a length, L =1.40 m . The tension in the string is 12.0 N. The box has a tangential velocity of 2.60 m/s and is moving on a level, horizontal surface which has a co-efficient of kinetic friction of 0.253. The co-efficient of static friction is unknown. side view top "bird's eye" view L VT
In the figure, a 58 kg sphere is supported on a frictionless plane inclined at angle 0 = 42° from the horizontal. Angle p is 23°. Calculate the tension in the cable. Cable 9. Number Units the tolerance is +/-1 in the 2nd significant digit Click if you would like to Show Work for this question: Open Show Work
#5
When Jenny couldn't lift a box by herself, she decided to use a lever to move it. She placed a fulcrum 1.6 m away from the box and used a 2.0 m lever to try to lift the box. Her effort was still unsuccessful. Explain why Jenny was unable to lift the box with her lever, and suggest a way she can adjust the lever to improve her chances of success. Use math to support your answer. Answer using 3 to 5 complete sentences and/or math problems.