9. A certain fan delivers 12,000 cfm at a static pressure of 1 in water gauge when operating at a speed of 400 rpm and requires an input of 4Hp. if the same installation is 15,000 cfm desired, what will be the new power needs in Hp?

Q: 1. AB=X 2. A+B=X 3. X=A 4. ABC=X 5. AB+CD=X 6. AB+A=X Page | 4

A:

Q: Prioritize the following line types. If a line type is prioritized, that means that it will be…

A: Given Lines To find Highest priority line in engineering drawing

Q: 1-The graphitization of cast iron effected by ………………………..? 2-The hardness test…

A: The graphitization of cast iron effected by keeping the material in elevated temperatures for long…

Q: Q5- put a/an before the count nouns, and some before the un-count nouns. 1- A chair 2- --- petrol 3-…

A: A count noun is a noun that something countable. For example, A man, tree, Books, etc, And Non-count…

Q: Sketch the right oblique view name front view(F) and top view(T) and side view (S) on the sketch…

A:

Q: EX7: write a program read any vector and print the odd order only?

A: Required: Program to read vector and print item ad odd order.   all the code with code screenshot…

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: Draw a general schematic of this water-heating system with main inlet, branch pipes (for 1st to nth…

A:

Q: I need the answers to this part, I have submitted this question twice on this site and both times…

A: Sampling length – 5 Minimum material to be removed is specified -  1 Rough machine finish – 3…

Q: b)Calculate Degree of freedom for the following figure. Activate Windows Go to Settings to activate…

A:

Q: QI\ AFind the value of the complex number (1- i) ?

A:

Q: 1. drawing provides information about size and tolerances for the manufacture of the parts. 2. The…

A: Given Drawing To find Fill in the blanks

Q: Create a list of operations for the blueprint provided below. The list of operations must be in…

A: The chronological order of operation of the given part is mentioned below  for this part the list of…

Q: As the fish looks at you, does your head appear to be at a greater or lesser height above the…

A: The light rays reflected from the fish are refracted at the water's surface, but the eyes and…

Q: Determine the skin due to perforation for a vertical well completion scheme described below: Payzone…

A: To Find:the skin factor due to perforation for a vertical well completion scheme.Given:The pay zone…

Q: Can you help me with this problem? P1 is where the blue dot is

A: 1. N10 G90 - Set to absolute positioning.2. N20 G54 - Select the work coordinate system.3. N30 G00…

Q: Q5-Rewrite the sentence using the word between the bracket

A:

Q: Write the function of ortho on in an AutoCAD system. When and why we use this command during…

A: Ortho System In AutoCAD, the Ortho mode is used to limit the movement of cursors to certain…

Q: what is the cause of an extremely hard brake pedal

A: To the left of the accelerator, the brake pedal is positioned on the floor. It applies the brakes…

Q: General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single…

A: Fill in the blanks

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: 1) The density of a metal, which has the BCC structure and one atom per lattice point, is 0.855…

A: given data: density of metal in bcc structure=0.855g/cm3 atomic weight =39.09g/mol

Q: Hot water (specific heat of 4.18 Kj/kgK) at 66C is flowing through a metal pipe (6 m long, 2 cm ID,…

A: Given  Hot water is flowing through a metal pipe.  Specific heat of water = 4.18 Kj/KgK Temperature…

Q: I need answers for problems 13, 14, and 15 pertaining to the print provided.   NOTE: If you refuse…

A: 13.A characteristic of a system which may cause failure or defects if not in line with quality…

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: GIVEN THE ORTHOGRAPHIC VIEWS, CREATE AN ISOMETRIC SKETCH OF THE FOLLOWING OBJECT.

A: According to the given data Three projection view of an object is drawn We need to draw Isometric…

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Q: A centroid is an object's geometric center. For an object of uniform composition, its centroid is…

A: Hi, As per the guideline, we can not provide you with a handwritten solution.

Q: B -L-

A:

Q: Q1: write a program to enter any text and compute its length. Q2: Design a form with a text box. Use…

A: Python Program: str = input("Enter the string: ")                             print("Length of the…

Q: Please turn this into 3d drawing, measurements are not important.

A: According to the question We need to find 3-D model of the drawing

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.