9) Design a new pipe to replace ageing infrastructure, which is a series pipe system consisting of a 225m long pipe, D=0.3m and a 400m long pipe, D=0.5m. Use a single concrete pipe, k=0.3mm for the new design, and find the diameter required. Q=0.1m³/s (D=0.36m)

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: the sketch top, front, and right side isometric below. For the objects shown in sure that your views…

A: According to the details provided in the question we need to draw three projection view of the given…

Q: A particle travels along the circular path from A to B in 1 s. If it takes 3 s for it to go from A…

A:

Q: Given drawing of a Mechanical component, study the drawing carefully and then using Inventor, AUOB…

A: 1. Create the 3D Model of the part.

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: Write dimensions of work and please explain neately.

A: Given Data⇒ Work

Q: A solid cylinder is rolling down a ramp that is rough enough to cause the cylinder to roll without…

A: This question is solved with the help of the law of conservation of energy. Under pure rolling,  The…

Q: You can use a lever to increase force, distance, and speed.  True or false?   (simple machines:…

A: You can use a Class 1 or Class 3 lever to increase the speed of the load, according to where the…

Q: An air hockey table has dimensions as shown in the picture. 0.3m Usually, the air from the table…

A: according to the given data

Q: Design the solid model shown.  There should only be 4 sketches max and an applied feature. This…

A: according to the given details in the question.

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: The ball is kicked from point A with the initial velocity VẠ = 10 m/s. Determine the range R, and…

A: A reaction force opposes an action force by acting in the opposite direction. During sliding,…

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: Let me know if I have misinterpreted the question.

A: in this question all the help full values are given.In this question plate slider due to impact…

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: can this be done using simpsons rule?

A: As already calculated using the relation    for the volume ranging from to  in steps of , the…

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.