9-111. The symmetric concrete "gravity" dam is held in place by its own weight. If the density of concrete is P= 2.5 Mg/m³, and water has a density of p= 1.0 Mg/m³, determine the smallest distance d at its base that will prevent the dam from overturning about its end A. The dam has a width of 8 m.

9-111. The symmetric concrete "gravity" dam is held in place by its own weight. If the density of concrete is P= 2.5 Mg/m³, and water has a density of p= 1.0 Mg/m³, determine the smallest distance d at its base that will prevent the dam from overturning about its end A. The dam has a width of 8 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. A dam is triangular in cross-section with the upstream face vertical. Water is flushed with the top. The dam is 8m high and 6m wide at the base and weighs 2.4 tons per cubic meter. The coefficient of friction between the base and the foundation is 0.8. Determine (a) maximum and minimum unit pressure on the foundation, and (b) factors of safety against overturning and against sliding. (* 6. A gravity dam of trapezoidal cross section with one face vertical and horizontal base is 22m high
Subject: Statics of Rigid Body Show Complete solution
3 A masonry dam 21m high, has a triangular cross section. The upstream side being vertical. The masonry weighs 23.544 kN/m". The water depth at the upstream side of the dam is 18m. Calculate the width of the base of the dam if the resultant reaction at the base is located 4/10 B from the toe. Round off your answer to a whole number. Answer: B = m 21m 18 m B = ?
30 kN/m 45 KN•M В A- -1.5 m- -1.5 m- -1.5 m Problem 6-22 Hibbeler 10 kN 10 kN 15 kN-m B -2 m 2 m 2 m For the above problems 1. Calculate support reactions 2. Establish SF and BM equations for each cross-section of the beam 3. Construct the SF and BM diagrams for each beam 4. Determine the maximum SF and maximum BM and their respective positions 5. Determine the position of PCF (if any) for each beam
The height of the reinforced concrete water dam in the figure is L width a. The unit weight of the body of the dam Su gola Betogarme su bendi is y=24 kN/m'. Since the height of the water lake is h and the lateral water thrust to the body is H=5h? kN/m, determine the maximum water height (hmax) to avoid 4. tensile stress at the base of the dam. (L=15m, a=7m) Note: Calculate for unit height (taking 1 m),
Figure 2 shows a 0.8 m wide of rectangular sluice gate is hinged at point A on the wall of a reservoir, which is inclined at 30° to the vertical. The vertical distance between the water surface to the point A is 8 m. Solve, a. The resultant force and its centre of pressure vertically from the water surface to the rectangular sluice gate. b. The distance, h along the wall surface to the location of resultant force as shown in Figure 2. Water lavel Figure 2
Determine support reaction
There is a dam shaped like a semicircle with 45° angulation. The dam consists of two structures: one 20 m high, generated by a second degree function, and the other rectilinear 10 m high. The forces on the dam should be analyzed in order to prevent its rupture. Determine: A) The graph of the resulting force as a function of the water height at the bottom of the dam B) The resulting force for a water height of 10 m C) The resulting force for a water height of 20 m 5,0 m 10,0 m 30,0 m 17,5 m
A 4m long, 2m wide, and 3m high tank is completely filled with water. Solve the resultant hydrostatic force at the base. 294.2kN O 235.4kN O 197.7kN O 258.9kN
1. A masonry dam of trapezoidal cross section, with one face vertical and horizontal base. The dam is 8-m high and has a thickness of 70-cm at the top and 4-m at the bottom. The unit weight of the masonry is 23.450 N/cu.m. What is the depth of water on the vertical side if the resultant force intersects the base at the downstream edge of the middle third. Neglect the hydrostatic uplift.
A vertical bulkhead 4.8m wide divides a storage tank. On one side of the bulkhead petrol (S.G. = 0.78) is stored to a depth of 2.36m and on the other side water is stored to a depth of 1.2m. Determine the resultant force on the bulkhead and the position where it acts.
A masonry dam of trapezoidal cross section, with one face vertical, has a thickness of 1m at the top and 3m at the bottom. It is 7m high and has horizontal base. The vertical face is subjected to water pressure, the water standing 4.5m above the base. The weight of the masonry is 23.5kN/cu.m. Assuming no hydrostatic uplift, where will the resultant pressure intersect the base, and what will be the intensity of pressure at the heel and toe.