(kN)-12.5Identify the loaded beam where thisshear diagram is from.50 AN10 KNim10 kNim50 kN5m5m5m. 10 Nim50 KNO25m5.m.5.m10 kNm50 AN5m5m5mSm.5m

Answered: 875 V AN) -125 25 Identify the loaded…

Engineering

Mechanical Engineering

875 V AN) -125 25 Identify the loaded beam where this shear diagram is from.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P= 4 kN w= 0.8 kN/m a) Start with the shear diagram. To use a segment of the left end of the beam to develop the expression for the shear, the vertical reaction at A must be known. Calculate the vertical reaction at A. Let a positive force act up. b)Write an expression for the internal shear for an arbitrary point between A and B c)Write an expression for the internal shear for an arbitrary point between B and C.
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given figure. Given: P = 610 N. C A D 200 mm 200 mm 200 mm P B Draw the shear and bending-moment diagrams for the beam AB. (You must provide an answer before moving on to the next par (Please upload your solution/response using the controls below.)
87.5 V C (kN) -12.5 -62.5 Identify the loaded beam where this shear diagram is from.
Consider the beam and loading shown where Mp=3700 lb-in. 600 lb 600 lb M₂ do E 12 in. 8 in. From the figures given below, identify the correct shear diagram and determine the maximum absolute value of the shear. Shear F Shar a Foce C Figure 1 D 12 in. Figure 3 The correct shear diagram is Figure 2 The maximum absolute value of the shear is ► x( (N lb. S mi A S Face A D Figure 2 D Figure 4 40 w
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
Draw the shear force and bending moment diagrams for 2 kip the beam under the external loadings shown in the figure. 200 lb/t Note use the graphical method; show all the critical tuming points of each curve, along with the calculation steps used in determining the critical points. 9
In (Figure 1), w = 3.8 kip/ft and F=20 lb. Follow the sign convention. Part A Determine the shear force acting at point D of the beam. Express your answer in kilopounds to three significant figures. vec VD = kip Figure 1 of 1 Submit Request Answer Part B Determine the moment acting at point D of the beam. Express your answer in kilopound-feet to three significant figures. A, 6 ft 9 ft ΑΣφ vec MD = kip ft %3D
Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the questions as a check on your work. when x = 10, V= ? M= ? Absolute Vmax= ? Absolute Mmax= ? Round your answers up to 3 decimal places.
Identify the correct boundary conditions from the following list for the beam shown. The origin is at A. B L O v = 0 at x = L; dv/dx = 0 at x = L O v = 0 at x = L; dv/dx = 0 at x = 0 O v = 0 at x = 0; v = 0 at x = L O v = 0 at x = 0; dv/dx = 0 at x = 0 O v = 0 at x = 0; dv/dx = 0 at x = L
Assume the support at B is a roller. Point C is located just to the right of the F = 13-kip load. A) Determine the internal normal force at point C. NC = ? B) Determine the shear force at point C. VC = ? C) Determine the bending moment in the beam at point C. MC = ? D) Determine the internal normal force at point D. ND = ? E) Determine the shear force at point D. VD = ? F) Determine the bending moment in the beam at point D. MD = ?
Please answer and draw Shear and Moment diagram.