84. A 2,400/2,200-volt autotransformer delivers a load of 90.5 kw at a power factor of 0.75. transformer, Calculate the current in each winding section and the kva rating of the 34

Q: The characteristic of the UJT exhibits the following values: n = 0.575, R81 = 10 k-ohms, Vv = 1.3 V,…

A: a) According to the intrinsic stand off ratioη=RB1RB1+RB20.575=10k10k+RB2RB2=7.39kΩ

Q: List two examples and explain the reasons regarding to the behavior of power electronics device…

A: Based on their ON and OFF condition of the Power Electronics devices it can be categorizes in three…

Q: H.W2 The single-phase full wave controlled rectifier has a R-L load with R= 0.52 and L= 6.5mH. The…

A: vs=Vm=220VR=0.5ΩL=6.5mHα=600ω=2πf=2π×50=100πAsked to find the followingThe average thyristor…

Q: Perform the following number system conversions and name the method that you use (Summation,…

A: Note: As per our company guidelines we are supposed to answer only the first three sub-parts. Kindly…

Q: 8. What is the primary difference between the BJT and the FET? a. current-controlled device and…

A: From the given options we need to determine the primary difference between the BJT and FET. BJT: BJT…

Q: Discuss monostable multivibrator by directly stating it circuit diagrams, output waveforms, and…

A: Given:Monostable multivibrator.Required:We need to discuss the monostable multivibrator by directly…

Q: Discuss Astable multivibrator by directly stating it circuit diagrams, output waveforms, and…

A: Given:Astable multivibratorRequired:We need to discuss the Astable multivibrator by directly stating…

Q: 4. Build an AND gate using transistors, switches and LEDs. Pressing the switch should emulate…

A:

Q: Clipper circuit: Vi (p-p)= 10 volt (Sinewave) F=1 kHz R= 10 Kohm V= 4 volt Find and Sketch the…

A:

Q: Power Electronics.   Write necessity of power supply and briefly describe different types of SMPS…

A: Power supply: It is an electronic device  that supplies electric energy to an electric loads the…

Q: Enumerate and define the classification of electronic communication

A: Communication is the way of expressing the thoughts in the form of messages from one end to the…

Q: What is/are the significance of using Tinkercad? Why do we need Tinkercad? Explain. What are the…

A:

Q: Propagation delay is usually measured in a. milli-Watts O b. nano-seconds O. nano-Watts O d.…

A: We need to tell about unit of propagation delay.

Q: Answer it ASAP..

A: Two way multiplexer  It is defined as 2n×1 mux Here n=1 that means one selected line with this MUX…

Q: First let's clarify that this question concern digital circuits "IC" do now if that makes difference…

A: A Bistable Multivibrator is a two-state electronic circuit, also known as a flip-flop, with stable…

Q: A uniform quantizer, with average quantization power of 67.5 mW, is used in a PCM system. 1) What is…

A:

Q: Discuss Waveform generator by directly stating it circuit diagrams, output waveforms, and principle…

A: It is asked to discuss Waveform Generator through its circuit diagram, output waveform, and…

Q: IV) What is Cell Relay? Give applications.

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: Electronic methods of communication have several benefits. Do you know of any cons associated with…

A: Introduction Electronic communication: Electronic communication is described as a form of…

Q: 1. Are the following statements correct or wrong? a) Thyristors are used only for low voltage, low…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Punch Trough IGBTs have........... voltage blocking capabilities.

A: The IGBT is insulated-gate bipolar transistor. Based on structure the IGBT classified as, Punch…

Q: 1. Are the following statements correct or wrong? (a) Thyristors are used only for low voltage, low…

A: We are authorized to answer one question and three subparts at a time, since you have not mentioned…

Q: 1. Perform the following number system conversions: a. (366)7 = ?10 b. (A24C.5)16 = ?10 c. (815.6)10…

A:

Q: select one quickly Synchronous counter is ........... than asynchronous counter. a) faster, b)…

A: Synchronous counter is counter which clock input for each flip flop given at a time and output of…

Q: When the pinch-off voltage is exceeded, ID will ____ as VDD increases.   a. double   b.…

A:

Q: Subject is Communication system. In a public switch telephone network (PSTN),how the analog speech…

A: There are majorly three steps for converting analog signal to digital signal. 1. Sampling of the…

Q: 1. Draw the internal design of a microcontroller and explain each block diagram. 2. What are the…

A:

Q: A new networking technologies and new Internet applications continue to emerge. Some of the most…

A: Given data: Topic Transition Telephone system Switch from ...... to........…

Q: 1. Briefly describe the AMPS system. Describe also the three classifications of AMPS cellular…

A: Telephone communication-  Telephone communication is a defined as a communication in which the…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.