8.48 The switch in the circuit in Fig. P8.48 has been inPSPICE position a for a long time. At t = 0, the switch movesinstantaneously to position b.MULTISIMa) What is the initial value of vq?b) What is the initial value of dva/dt?c) What is the numerical expression for va(t)for t > 0?Figure P8.48100 NaЬ 20012 Ω+t = 0300 V+Va2 mH5 µF

Here the system is source free second order system. The circuit is series RLC circuit. The relation…

8.48 The switch in the circuit in Fig. P8.48 has been in PSPICE position a for a long time. At t = 0, the switch moves MULTISIM instantaneously to position b. %3D a) What is the initial value of v,? b) What is the initial value of dvaſdt? c) What is the numerical expression for va(t) for t > 0? Figure P8.48 100 N a 20 N 12 Ω t = 0 300 V + 2 mH Va 5 μF

8.48 The switch in the circuit in Fig. P8.48 has been in PSPICE position a for a long time. At t = 0, the switch moves MULTISIM instantaneously to position b. %3D a) What is the initial value of v,? b) What is the initial value of dvaſdt? c) What is the numerical expression for va(t) for t > 0? Figure P8.48 100 N a 20 N 12 Ω t = 0 300 V + 2 mH Va 5 μF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Problem 7: find the phasors of the following time functions: a. v(t) = 9 cos (wt - 7) (V) b. v(t) = 12 sin (wt + 7) (V) c. i(x, t) = 5e-³xsin (wt +) (A) d. i(t) = −2cos (wt + ³7) (A) e. i(t) = 4 sin (wt + 7) + 3cos (wt - ) (A) 3
Figure 8 showsa resistor inductor capacitor (RLC) circuit. The input to the system is the voltage v(t) and the output of the circuit is the current iz (t). 8 R, i(t) iz(t) v(t) Ve(t) R2 Figure 8 a) Determine differential equations containing i, (t), iz (t) and v. (t) for the appropriate meshes and nodes. b) Assuming zero initial conditions i) derive Laplace transformations of the differential equations found in a) ii) determine the transfer function G(s) = I2(s) VIs where l2(s) = L{i2 (t}} and V(s) = L{v(t}.
For the circuit given below, assuming zero initial conditions for t<0, obtain the equation giving the natural solution of the circuit and obtain the damping frequency in terms of the given ones
12V Q2: For the transient RL circuit shown below use differential equation method to find the current io (t> 0). How much is the stored energy in the inductor after t = 5 sec. mi 65 t-o 24 122 Y ₁0 (A)
In the circuit shown, the switch indicated open for a very long time, and then closed at t=0. When the switch moves, there is a transient response in the inductor current (indicated on the diagram as i). The component values are R1 = 1.1 k0, R2 = 2.2 k0, R3 = 2.2 kQ, L = 80 mH, C = 90 nF, Vs = 3 V. VS Q= + 2 No. 20 1 R1 Ω ww +1₁ R2 Ω + m V t= LH m Find the quality factor of the transient response (i.e. Q), to within 1% precision. > Okok
9. At t = 0, the switch in the circuit below opens. Prior to t = 0 the circuit is in steady state. Find iL(t) for all times, if L = 1 H. Sketch iL(t) vs. t. 0.2 F t = 0 20 IL 5 A ( 10. Repeat problem 9 if L = 0.2 H.
Hello, I would appreciate greatly if you could solve for i(t) and give a thorough explanation of your reasoning/approach
Question(6): The switch (S) in the circuit shown in Fig. 6 has been opened for a long time. At (t-0) the switch is closed. Find an expression for the inductor current and voltage for t>0? ww 2n3 100mtt 12V Fig.6 od Luck Dr. Tarek Kan Dr. Mohamed Mehanna
SOLVE STEP BY STEP IN DIGITAL FORMAT DONT USE CHATGPT 8. 8. Find the voltage across the capacitor as a function of time for t>0 in the circuit the following figure. Assume steady state conditions exist at t = 0. 20 V 592 www t=0 1Ω ww 0.25 H 1 F
8.2 From the circuit in the figure, if the switch is closed for a long time and opens at time ? = 0. Find ?(?) when ? > 0
During the transient analysis of an RL circuit, if the current through an inductor is 1.5 A at t = 0, the current through that inductor at t = (0.5 time-constant) will be: O A. Higher O B. The same O C. Lower O D. None of the other choices are correct O E. Can't tell the current until we know the voltage applied to the circuit
8.27 Solve the following differential equations subject to the specified initial conditions (a) d'v/dt? + 4v = 12, v(0) = 0, dv(0)/dt = 2 (b) d²i/dt² + 5 di/dt + 4i = 8, i (0) = –1, di (0)/dt = 0 (c) d²v/dt? + 2dv/dt +v = 3, v(0) = 5, dv (0)/dt = 1 (d) d²i /dt? + 2 di/dt + 5i = 10, i (0) = 4, di (0)/dt = -2