8.14 (B). Calculate the minimum diameter of a solid shaft which is required to transmit 70 kW at 600 rev/min if the shear stress is not to exceed 75 MN/m². If a bending moment of 300 Nm is now applied to the shaft find the speed at which the shaft must be driven in order to transmit the same horsepower for the same value of maximum shear stress. [630 rev/min.]

8.14 (B). Calculate the minimum diameter of a solid shaft which is required to transmit 70 kW at 600 rev/min if the shear stress is not to exceed 75 MN/m². If a bending moment of 300 Nm is now applied to the shaft find the speed at which the shaft must be driven in order to transmit the same horsepower for the same value of maximum shear stress. [630 rev/min.]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanics of deformable bodies
11.5 (A/B). Two shafts, one of steel and the other of phosphor bronze, are of the same length and are subjected to equal torques. If the steel shaft is 25 mm diameter, find the diameter of the phosphor-bronze shaft so that it will store the same amount of energy per unit volume as the steel shaft. Also determine the ratio of the maximum shear stresses induced in the two shafts. Take the modulus of rigidity for phosphor bronze as 50 GN/m2 and for steel as 80 GN/m?.
None
8.4 (A). A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to exceed 60 MN/m² nor the angle of twist 0.3° per metre length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m² [61.5 mm.]
Example 7.5: (Numerical problem of a circular shaft) A circular shaft 10 cm diameter and 1.1 m length is required to transmit power with a maxi- mum angle of twist of 3°, (a) What is the maximum possible torque that can be transmitted by this shaft? (b) Find the maximum shear stress induced. (c) Find the maximum possible power transmitted for N = 1500 rpm. Given that modulus of rigidity G 8% 101M Pa.
Problem 3.2, don’t do any other question, just problem 3.2
Find the length of solid shaft (L=?) in the rolling mill transmits 10KW at frequency 2r/s. Diameter of the shaft is 60mm. #f the shearing stress is not exceed 60MPa and the angle of twist is limited to 5°. G=836 836P2 Length of Shaft, -L=?
2. Two shafts, one solid the other one hollow, are connected end to end by means of a coupling in which there are 8 screws on the pitch diameter D = 250 mm. The solid shaft has diameter d = 50 mm and transfers the power P = 500 kW at 75 rev/s. The external diameter of the hollow shaft is dex = 75 mm. %3D Note: All parts of the system must be equally strong, and able to transfer the required power Calculate: (a) The internal diameter d; of the hollow shaft (b) The diameter of the bolts d, connecting the two shafts (c) If the hollow shaft has to be replaced by a rectangular hollow cross-section with outer dimensions b xh and uniform wall thickness of 4 mm. Calculate the values b, h while following the request to keep h = 2b
A hollow steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 1deg in a length of 26 diameters. Compute the proper diameter if Do =2Di. Show your complete solution.
A shaft is used to transmit 55 kW power at 500 rpm is subjected to a bending moment of 450 Nm. Calculate the diameter of the shaft if the shear strength of the shaft is 180 MPa.
A hollow aluminum propeller shaft, 30 ft. long with 15 in. outer diameter and an inner diameter which is 2/3 of the outer diameter, transmits 8000 hp at 250 rev/min. Use G=3.5x106 psi for aluminum. Calculate (a) the maximum shear stress; (b) the angle of twist of the shaft.