8. Given the following data for the number of defects per spool of cable, using three-sigma limits, is the process in control? OBSERVATION 1 2 4 6 7 8. 9. 10 11 12 13 14 Number of defects 1 0 1 3 2 0 1 1 2 3. 3. 3. 2.

Q: Worksheet 6-3 00 1. Type of view 2. Type of view 3. Type of view 4. Type of view 5. Is view 4 easier…

A: Solution: Given Data:

Q: ADD MISSING LINES (VISIBLE OR HIDDEN) TO EACH OF THE PROBLEMS BELOW. XX * 30

A: Given: Photographic views: Top view, Front View and Right View.To draw: Missing lines for each…

Q: 2. Draw the sketch of 'Drilling machine' and explain any four parts. Use pencil to draw the neat…

A:

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Draw the top view  front view  right side view  on graphing paper please. Put measurents if…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Draw digitally a unique, original design of a decorative block. Please refer to the sample picture…

A: A decorative block can be any type of block or object that is used for ornamental or aesthetic…

Q: A bcc (111) surface has the following (3x1) adsorbate structure: Select all of the following LEED…

A: Solution: Given Data:

Q: The correct choice is what

A:

Q: In Figure below, the main issue is with the leader representing which item?

A: Given:- An engineering drawing To find: Which representation is wrong

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: What kind of font is typical for usage in engineering diagrams?

A: To find: The type of font used in engineering diagrams.

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: Please make draw the right-side view, front view, and top view of the given isometric drawing.…

A:

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: Discuss how the Cylindrical Square is used.

A: A cylinder square is used for checking the squareness of vertical axis with reference to horizontal…

Q: can you please write it in a proper way?

A:

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: FORTUNE FAVOURS THE BRAV

A: A week ago our little villa was invaded by fear-based oppressors. There was dread in the seniors.…

Q: Orthographics: Add missing lines and complete any missing views. Draw the isometric

A: The missing lines of the given views are shown below.

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: need answer in 15 minute's please 3 (29// A ruck is throw up according to equation s(t) = { +2E-6t…

A:

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: Choose the correct word to complete the -5 following sentence: The fault was.......... .None of the…

A: Correct answer: (c) undetected

Q: In creating orthographic views, each view must:

A:

Q: can you draw the FBD

A: There are four rivets in this problem. In ideal case load will be equally distributed. Each rivet…

Q: The circular pattern feature can be used in creating the following part. True False

A: Circular patterns are used to draw the circular solidworks diagram as shown in the given figure.For…

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: 10) Define the slip angle.

A: The angle between the direction of the wheel in which it is pointing and the direction in which it…

Q: 13- Drawing sheet table contains class item. O True O False 12- The drawing sheet can be used both…

A: 13. in drwaing sheet tables are used to specify each part and its materials to do machining  so the…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.