8. A flat plate ( 1.5 m ) long and ( 1.5 m) wide is towed in water ( p = 1000 kg/mand v=1.31 * 10 “ m / s) in the direction of its length at a speed of ( 20 cm /s).Determine;a) The skin frictional drag force on both sides of the plate.b) The boundary layer thickness at the end of the plate.

The given values are length l=1.5m, width b=1.5m, density ρ=1000kg/m3 , kinematic viscosity…

8. A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water (p = 1000 kg/m and v=1.31 * 10 “ m² / s) in the direction of its length at a speed of ( 20 cm / s ). %3D Determine; a) The skin frictional drag force on both sides of the plate. b) The boundary layer thickness at the end of the plate.

8. A flat plate ( 1.5 m ) long and ( 1.5 m ) wide is towed in water (p = 1000 kg/m and v=1.31 * 10 “ m² / s) in the direction of its length at a speed of ( 20 cm / s ). %3D Determine; a) The skin frictional drag force on both sides of the plate. b) The boundary layer thickness at the end of the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question B3 – External Flow The rectangular wings of a microlight aircraft have a combined spanwise length of 9.144 m and streamwise (direction of air flow) width of 0.9144 m The wings have a coefficient of form drag of 0.01 and a lift coefficient of 0.3 in cruise. When cruising at a speed of 15Okm/h and altitude of 3,000 feet, the temperature and absolute pressure of the atmospheric air are 5°C and 90 kPa, respectively. a) Calculate the density of the air at cruising altitude. b) Calculate the form drag on the wings. c) Calculate the Reynolds number of the wings.
A 30-cm-diameter smooth ball of density Phall = 210 kg/m³ is tied to an object on the bottom of a river as shown on the right. Determine the angle 0 when the speed of the river current is a. U = 1.66 m/s b. U = 0.13 m/s c. For which velocity, the drag coefficient is lower? Explain why? 30° Take the density and viscosity of water in the river Pwater = 1000 kg/m², µwater = 0.001 kg/m's. Neglect the weight of the cable and the drag on it. 400 200 100 80 60 40 20 10 0.8 0.6 0.4 0.2 0.08 0.06 2 4 68 10- 2 4 68 2 4 68 2 4 68 102 2 4 68 103 pvd 2 4 68 10 2 4 68 10 100 10 105 Reynolds number, Drag coefficient, Cp
A 29-cm-by-47-cm block slides on oil (μ=0.81 Pa-s) over a large plane surface. What force in Newton is required to drag the block at 3 m/s, if the separating oil film is 2 mm thick?
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.
A supertanker is 300 m long, 80 m wide (beam), and 25 m deep (draft). The ship moves at 14 knots through seawater at 4°C. Determine the following: (a) the thickness of the boundary layer at the stern of the ship. (b) The total skin drag acting on the tanker (c) The power required to overcome the drag force
A smooth square billboard 5 × 5 m² is place on a roof of a tall building. In orienting the billboard, the engineer is considering the wind direction for two possible cases: (a) the wind is parallel to the board (b) the wind is perpendicular to the board. Assuming maximum wind velocity of 10 m/s, what will be the force acting on the billboard in each of the cases considered? (Use u = 1.85 x 10-5 kg/m – s; p= 1.225 kg/m³; Recr = 500,000) %3D
A high speed train has a design speed of 120 km/hr. A flat plate of length 200 m with a width of 9 m is used for the simulation of train. Determine the approximate power required to overcome surface frictional resistance . ( Air density :1,2 kg m3 viscosity: 1,5 x 10-5 m2/ s )ANSWER: 69,6 k W
3) An advertising sign mounted on the roof of a car is 33 inches tall, 15 inches wide and 54 inches long (airflow direction). The underside of the sign is flush with the top surface of the roof. Take air properties to be: p = 0.075 lbm/ft' and u= 1.22x10 lbm/ft.sec. Used a pressure drag coefficient of 1.2 for the advertisement sign. Calculate the total drag on the sign and the power required to overcome its effect if the car is travelling at a constant speed of a) 12 mph and b) 45 mph. Note: Provide a schematic diagram (sketch) of the problem configuration (if applicable). Every numerical calculation must be preceded by the appropriate equation. Do not forget units & dimensions during your calculations.
A block, as shown below, is sliding on a thin horizontal layer of water (u = 1.68 x 103 kg/m.s) between ice and the block with a speed of 13 m/s. The thickness of the water layer is 3.32 x 10-5 m. Given the following dimensions of the block, what is the force (F) required to maintain this movement? A = 9 cm B = 9 cm C= 8 cm B 2.96 N 5.33 N 4.14 N 4.74 N
A portion of ship’s hull can be idealized as a flat plate, 100ft long. If the ship’s velocity is 10 ft/s and the properties of the water it is moving through are ρ=62.4lbm/ft³ and µ=3.0lbm/hr.ft, calculate the maximum boundary layer thickness.
Question A3 a) With the help of sketches briefly describe the main differences between laminar and turbulent boundary layers in relation to friction drag and flow separation. A tug boat is pulling a log raft (Figure QA3) on the surface of a lake at a constant speed of Uboat = 5m/s. The log raft can be modelled as a flat plate (L=20m and W = 5.0m). u ug U boat 8 U Tug Boat rope boat Air Water L -X Log Raft Figure QA3 Assume the boundary layer forming on both sides (air side and water side) of the log raft is two-dimensional and laminar with a second order velocity distribution: W b) By using the Momentum Integral Equation find an expression for the wall shear stress in terms of Reynolds number and then estimate the tensile stress acting on the rope assuming the rope has a circular cross section with a diameter of 15 mm) and the power required to pull it. c) What would be the tensile stress on the rope if we assume the boundary layers on the log raft were turbulent? You may assume:…
You are designing an airfoil for a new hobby RC plane. Because of your limited knowledge, you have mistakenly approximated your airfoil as an ellipse with a = 75mm and b = 12mm. Here, “a” is the depth of your wing and “b” is the thickness. Your plane travels through the air at approximately 20mph (8.9m/s). As it does so, skin friction produces a drag-induced heat of 800W on your wind, of length 1m. Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the Reynold’s number? Hint: “D” is taken to be the thickness for an elliptical crosssection. b) What is the Nusselt number? c) What is the convection coefficient? d) What is the average temperature of your wing? Assume an ellipse perimeter of approximately 200mm.