8 kN 4 kN 0.6 m 0.9 m

Q: P

A:

Q: Horizontal plates are connected to the bar AB whose length varies linearly from zero to HA, as…

A:

Q: The block is subjected to axial loa normal tension developed at poir the distribution of the normal…

A:

Q: The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the magnitude of the…

A:

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: Determine the stress in the cable BC if the mass of the cylinder is 250 kg. The cross sectional area…

A:

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: The beam is subjected to the load at its end. Determine the maximum principal stress at point B.

A: Determine normal stress due to axial load Due to shear load there will be bending moment at B…

Q: Determine the shear stress at point A and point B with appropriate units

A: Givendiameter of shaft d=80mmT=500Nm

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

A:

Q: Q2: If the block is subjected to the centrally applied force of 600 kN, determine the average normal…

A: Given: the block is subjected to applied force =600 kN we have to find the average normal stress in…

Q: At point A & C, the beam is pin connected. Therefore, find the average normal stress in the…

A:

Q: Problem 4: Determine the resultant intermal loadings acting on the cross section through point B of…

A: To determine the internal reactions at point B.

Q: The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial…

A:

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-16 aluminum. If a couple forces P =…

A: As applied force is at some distance from the longitudinal axis. so it generates torque and the…

Q: Two fully loaded tractor trailers travel over the bridge putting substantial loading on the…

A: The objective of this question is to calculate the shear strain at point T when a vertical…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: The beam supports the loading shown. Determine the state of stress at points E and F at section a-a.

A:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: Determine the force required to produce stress of 2 N/mm2 if cross sectional area is 2 mm2

A: Given data : Cross sectional area=A Stress=σ   Required : Force

Q: The steel rod having a diameter of 1 in. It is subjected to an internal moment of M= 200 lb⋅ft…

A:

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial…

A:

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: The solid bar has a diameter of 50 mm. The two forces and the x-y-z coordinate system which is…

A:

Q: The bar has a cross-sectional area of 350(10-6) m². It is subjected to a uniform axial distributed…

A:

Q: Determine the maximum axial force P that can be applied to the bar. The bar is made from steel and…

A: At the failure of the fillet To find out the concentration factor, K rh=0.251.25=0.2…

Q: The central pillar B of the system has a length of 124.7mm in the beginning, while the a and c…

A: LB=Original length of center post =124.7 mmA=Cross sectional area of each post =400 mm2=400×10-6 m2

Q: The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip,…

A: Given data:-  the applied force P=1.50 kip diameter 1.5 in To find: The maximum normal stress (ksi)…

Q: Determine the equivalent state of stress on an element at the same point oriented 60°…

A: Given Data: The value of σx=150 MPa The value of σy=100 MPa The value of τxy=75 MPa The orientation…

Q: Determine the maximum compressive stress in the bracket at section a–a when the load P = 52 kN is…

A:

Q: A crane is supported by two cables with a cross-sectional area of 3.04 cm2 each. Determine the…

A: A=3.04cm2 = 304mm2 Assume P=20KN , Mass of the boom = 450kg

Q: Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer…

A: Find outstate of stress at point q.Giventhe inner diameter of the pipe the outer diameter of the…

Q: Determine the equivalent state of stress on an element at the same point oriented 45° clockwise with…

A: Given Data: The value of σx=0 The value of σy=-400 kPa The value of τxy=-300 kPa The angle of…

Q: If the load has a weight equivalent to 5 kN, determine the maximur hormal stress on the cross…

A: Given Data Load is :P=5 kN=5000 N Radius of circle is :r=2 cm=20 mm Distance of CD is : LCD=50…

Q: The bar has a 80 mm by 20 mm rectangular cross section. If P = 90 kN, determine the normal stress…

A:

Q: A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa,…

A: given; σx=8MPaσy=4MPaτxy=3MPa

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.