3-72. The ring of negligible size is subjected to a verticalforce of 200 Ib. Determine the required length /of cord ACsuch that the tension acting in AC is 160 ib. Also, what isthe force acting in cord AB? Hint: Uise the equilibriumcondition to determine the required angle 8 for attachment,then determine / using trigonometry applied to AABC.40V 200 Ib

Answered: Image /qna-images/answer/774bf8f6-e64d-47cd-98cd-83bf5b226581.jpg

-72 The ring of negligible sire is subjected to a vertical force of 200 lb. Determine the requircd length /of cord AC such that the tension acting in AC is 160 ih Aha what is the force acting in cord AB? Hine Use the equilibrium condition to determine the required angle for attachment, then determine / using trigonometry applied to AABC. 200

-72 The ring of negligible sire is subjected to a vertical force of 200 lb. Determine the requircd length /of cord AC such that the tension acting in AC is 160 ih Aha what is the force acting in cord AB? Hine Use the equilibrium condition to determine the required angle for attachment, then determine / using trigonometry applied to AABC. 200

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The crowbar is subjected to a vertical force of P = 27 Ibat the grip, whereas it takes a force of F = 160 lb at the claw to pull the nail out. The crowbar contacts the board at point A. Find the moment of the force Pabout point A. Find the moment of the force Fabout point A. Determine if Pis sufficient to pull out the nail.
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring at point D.
A BB-series Astromech Droid of mass 154 kg is suspended by the truss structure shown. The truss structure is pinned to the wall at A and is supported by a rocker against the wall at F. A B 2w E F Allow w = 3 m. Determine the forces in all the members in the structure and indicate whether they are in tension or compression.
ANSWER ONLY AC BC CDwrong answer gets downvote so double check the answer cause it will be input in the system
determine the reacction of th beam show in fig by using consistante deformatiom method . use the redundants Cy and Ey
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
Sokn 160KN ►20KN Bm A 나m Solve for the member force of member AC using method of joints indicate if its in tension or compression
Determine the internal normal force and shear force, and the bending moment in the beam at points Cand D. Assume the support at B is a roller. Point Cis located just to the right of the load P which is equal to 78.1N. Report the Bending moment in the beam at point D (Mp) here in Moodle. NB: • FBDS are required • Your answer should contain ALL the necessary steps
1. Answer Set A only
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
Consider a pinned moment frame with h = 120 in, L = 300 in, E = 4030 ksi, Ic = 1600 in^4, lb = 2lc, and W 1500 lb. Determine the period of the system in seconds 1.626
Problem 04.107 - Maximum load carrying capacity of a milled rod with known allowable stress A milling operation was used to remove a portion of a solid bar of square cross section. Knowing that a = 30 mm, d = 20 mm, and all = 54 MPa, determine the magnitude P of the largest force that can be safely applied at the centers of the ends of the bar. The magnitude P of the largest force that can be safely applied at the centers of the of the bar is KN.