70 mm -235 mm- 30 mm 30 275 mm 30 mm, 30 Prob. 6–101

Q: A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N. Determine…

A: To determine the direction cosine angles for a given force in 3-D.   From the given figure,…

Q: QV Replace the two forces acting on the bent pipe by a single oquivalent force R Specify the…

A:

Q: The bar AB is supported by two smooth collars. At A the connection is with a ball-and-socket joint…

A: Ax+Bx = 0By+50 = 0By=-50 lbAz+Bz = 0MBz= 0MBz+50(6) = 0MBz = -300 lb.ftBCD = -9i +3jBCD = -0.94868 i…

Q: A 10-m pole is held by a ball and socket at A, cable BE, cable BF, and cable CD, that is parallel to…

A:

Q: 3. There are four bolts used in the following figure for the connection and each is tightened so…

A: No slipping condition- No slipping condition means that there is no movement in between the two…

Q: 150 mm 140 mm 50 mm 60° 130 mm 45 600 N

A: Find the position vector: OA→=130cos30o+50i-130sin30o+140j+150kOA→=162.58i-205j+150k mm The force in…

Q: CDEFGH is plate with a circular hole in it and has a unit weight p (N/m²). It is attached on DE beam…

A: Center of gravity: The point in a system where the total weight or mass of the body is assumed to be…

Q: PROBLEM 03 A W, = 'ac' lb pipe is held in place by the vise. FA 30° FB B 50 lb

A:

Q: 8-4. Determine the magnitude of the load P that will max = 30 ksi in the link ause a maximum normal…

A: This question is related to the Strength of Material.

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel…

A:

Q: Find the reaction at hinge A, rollers B and D. Draw the FBD.

A:

Q: Determine the magnitude of the pin force at A. Assume W - 665 lb, a-2.6 ft. b-2.2 ft, r- 9 in. W…

A: GIVEN DATA:-⇒W= 665 lb⇒a= 2.6 ft⇒b= 2.2 ft⇒r= 9 in

Q: The bracket ABC can be supported in the eight different ways shown.All connections consist of smooth…

A: (1) There are three non-concurrent, nonparallel reactions. (a). The bracket is completely…

Q: Q-A rectangular plate 2m wide is submerged in water vertically such that its top & bottom surface…

A:

Q: 1.Calculare the Magnitude (absolute value) of the force in member CA in newtons.The correct answer…

A: m=26kg To find tension in cable CA and vertical component of reaction at point B

Q: F 10 in. 6 in. 8 in. 6 in. B

A:

Q: If a 100-N force is applied to the handles of the pliers, determine the clamping force exerted on…

A: The given figure is shown below:

Q: . Determine the rotation angle of pulley D with

A:

Q: For the beam and loading shown, determine the reaction at the roller support. Assume that the…

A: Given:Required:Reaction at roller support

Q: The toggle clamp is subjected to a force F at the handle. Determine the vertical clamping force…

A:

Q: Determine the magnitude of the pin force at A. Assume W-620 lb, a-4.6 ft, b- 3.1 ft.r-8 in. B b W…

A: The size of a force is measured by its magnitude. It's the sum of all the forces operating on a…

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 13 kN applied at A. Assume a…

A: Given data,  F1 = 13 kN θ = 45° A = 310 mm B = 160 mm C = 80 mm

Q: In the assembly shown. the block has a weight W =200 lbs and the cord is attached to the pin at B.…

A: To find reaction at link AB

Q: The bell-crank mechanism is in equilibrium for an applied load of F1 = 16 kN applied at A. Assume a…

A:

Q: 500 mm 1.2 kN -900 mm -750 mm -

A:

Q: The rigid bar ABCD is suspended from four identical wires. Deter-mine the tension in each wire…

A: Consider the free body diagram;

Q: (a) the normal strain in rod (2). (b) the normal strain in rod (2) if there is a 1-mm gap in the…

A:

Q: The rigid member is held in the position show by three steel tie rods. Each rod has an unstretched…

A: Given : Unstretched length = 0.75 mm Cross sectional area = 125 mm2 E steel = 200 GPa   To Find :…

Q: *R9 4. Two A36 steel pipes, cach having a cross-sectional area of 200 mm, are screwed together using…

A: Solution Given Data Cross-sectional area (A)= 200 mm2 young's modulus of elasticity E= 200 GPa =…

Q: The bell-crank mechanism is in equilibrium for an applied load of F, = 19 kN applied at A. Assume a…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.