7.5k2Q45 ΚΩ,Q₁-15V+15V:5K2VozQ₂5KR-oVozK₂Q31.2KS2Consider the BJT differential amplifier on the left.The transistor parameters are:Bn = 180; VBE (on) = 0.65V; and VA = 60V.Do NOT ignore intrinsic output resistances.V03(a) Calculate the differential gain Ad VaVos=(b) Calculate the common-mode gain AcmVem(c) Determine the output voltage Vosif v₁ = 2.015 sinct and v₂ = 1.985 sin wt.(d) Determine the differential-mode andcommon-mode input resistances.

Given The transistor parameters are: Beta n = 180 VBE (on) = 0.65V; and VA = 60V. And from the…

7.5k2 Q4 5 ΚΩ, Q₁ -15V +15V :5K2 Voz O₂ 5KR -oVoz K₂Q3 1.2KS2 Consider the BJT differential amplifier on the left. The transistor parameters are: Pn = 180; VBE (on) = 0.65V; and VA = 60V. Do NOT ignore intrinsic output resistances. Vo3 (a) Calculate the differential gain Ad Va Vos = (b) Calculate the common-mode gain Acm Vem (c) Determine the output voltage Vos if v₁ = 2.015 sinwot and v₂ = 1.985 sin wt. (d) Determine the differential-mode and common-mode input resistances.

7.5k2 Q4 5 ΚΩ, Q₁ -15V +15V :5K2 Voz O₂ 5KR -oVoz K₂Q3 1.2KS2 Consider the BJT differential amplifier on the left. The transistor parameters are: Pn = 180; VBE (on) = 0.65V; and VA = 60V. Do NOT ignore intrinsic output resistances. Vo3 (a) Calculate the differential gain Ad Va Vos = (b) Calculate the common-mode gain Acm Vem (c) Determine the output voltage Vos if v₁ = 2.015 sinwot and v₂ = 1.985 sin wt. (d) Determine the differential-mode and common-mode input resistances.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
VCC R2 RC- RI RL R1 RE VEE Assume: B=100, VA=150, Vcc=12V, VEE=GND, Rr=2K, R1=160K, R2=300K, RE=3K, Rc=2.2K, and R1=100K. Convert the circuit to a common-collector circuit. Draw the new circuit (assume the same values for the input and load resistances). Then compute the terminal voltage gain, and Rin (for the whole circuit), re-computing any parameters that you need to solve.
Find the desired in point 54 with finding what you can find.
Consider the two-stage amplifier in the figure below. The first stage is a differential amplifier and the second stage is a difference amplifier. Assume that Rg = 20k and you may ignore any early voltage effect. Further assume that Rc = 10k, R3 = 300k and R4 = 100k. What would be the estimated differential gain of the first stage amplifier? CRB close to 200 RB Q4 V01 Stage 1 Q3 O a. O b. close to 150 O c. close to 600 O d. close to 500 e. More information is required to calculate the gain Cm RC Q2 V02 RA R4 R3 Stage 2 -R3 741 + +10v į -10V
What is an active load circuit for amplifier? What is a driver circuit? What makes this unbalanced?
Please answer asap,thank you. The input of this is an AC signal with an amplitude greater than 3 and maximum frequency of 8khz(coming from an amplifier connected to this circuit). I am using this as a voltage follower. this CC amplifier sees the 5k resistor (from an amplifier buffer). Please design this CC amplifier such that the voltage swing is maximum. What values should i use for c1 and c2? Please explain the steps in detail.
Q4: Consider the uA741C-based op-amp amplifier circuit shown below; The input voltage, Vi, is 2.5 volts. R2 is 5,000 ohms and RI is 1,000 ohms : R2 vo • What is the name of the circuit? • What is the value of the voltage at the negative input of the op-amp? • What is the value of the current through the 1 k2 resistor, in?
Please solve with steps, using to study. Will upvote!
Note : Value of K1 = 17; K2 = 49 Show the each equation part and Mention ans same as asking in question. There are must be 2 graphs. Read the 2 pictures clearly and ans all the question. For Example : "Compare T+,T- , Draw the transfer characteristics V0 and V1 " Mention like this then ase the question. formula should be taken from "Operational Amplifier and Linear Integrated Circuits, by Robert F. Coughlin and Fredrick F. Driscoll, 6th Edition, Pearson." this book.
3ZD Calculate the output voltage of an op-amp if a 100mV signal is applied to the non-inverting input of the op-amp circuit which has an Rf = 0 Ohms and Ri = 0 Ohms. a.Infinity Volts b.0 Volts c.1 Volts d.-2 Volts
How did they get case 1 and case 2 and simplify break down for a dummy?
Select true or false for 1 and 21 Op amp component is temperature limited due to maximum output current2 The input offset voltage affects the value of the opamp output and is caused by internal non-idealities in the transistors and resistors. 3 What is the use of an op amp in voltage follower? Select one:a. It is the ideal bridge to couple any stages without affecting the voltage.b. It is ideal for maximum power transferc. Allows a small signal to be amplified with high gaind. voltage attenuation 4. It allows to eliminate the problem of variability in the gain parameter of the circuit:Select one:a. The load RLb. High input impedancec. feedback loopd. decoupling capacitors 5 Complete: The output current is limited due to the _____ that the opamp can handle, while the ______ is limiting due to the maximum bias level supported by the transistor.