7.11 Design a non-air-entrained concrete mix for a small job with a nominal maxi- mum gravel size of 25 mm (1 in.). Show the results as follows: a. masses of components to produce 2000 kg (4400 lb) of concrete b. volumes of components to produce 1 m3 (36 ft³) of concrete

7.11 Design a non-air-entrained concrete mix for a small job with a nominal maxi- mum gravel size of 25 mm (1 in.). Show the results as follows: a. masses of components to produce 2000 kg (4400 lb) of concrete b. volumes of components to produce 1 m3 (36 ft³) of concrete

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The testing of concrete for compression will require the preparation of 12 standard concrete cylinders with 150 mm diameter and height of 300 mm. The concrete mix proportion is 1:2:4 by weight and water cement ratio is 6 gallons per bag of cement. One(1) bag cement is 40 kgs, one (1) gal is 3.785 liters. The specific gravity of cement is 3.15, sand 2.60 and gravel is 2.70. Determine the mass of cement in kg needed for the 12 cylinders: 20.32 22.30 20. 23 23.02
Design of a concrete mix showed that 1 m3 of the mix contains 320 kg cement, 540 kg sand. A trial mix having the same proportions as the designed mix, enough for 6 standard cubes, containing 3.5 liters water was made. It is required to calculate the quantities by weight and volume for the construction of a concrete road having 25 m width, 1000 m long, and 0.25 m thick, given that the trial mix gave slump and compressive strength as designed.Specific density of cement = 3.15Specific density of aggregate (coarse or fine) = 2.7Unit weight of cement = 1440 kg/m3Unit weight of sand = 1600 kg/m3Unit weight of gravel = 1760 kg/m3 Using BSI Method Only
Calculate the maximum aggregate size for a concrete to be used for the beam the cross-section of which is given below. Note that 3 equally spaced 18 mm rebars with a clear cover of 40 mm is used in the beam, and 2 equally spaced 24 mm rebars per meter with a clear cover of 40 mm is used in the slab. (Show your calculations for each criteria) 024 mm slab 20 cm beam 40 cm 018 mm 30 cm הבה
Design a non-air-entrained concrete mix for a small job with a nominal maximum gravel size of 19 mm. Show the results as follows:a. mass of components to produce 2263 kg of concreteb. volumes of components to produce 1 m3 of concrete
Design a non-air-entrained concrete mix for a small job with a nominal maximum gravel size of 19 mm. Show the results as follows:a. mass of components to produce 2263 kg of concreteb. volumes of components to produce 1 m3 of concrete
The testing of concrete for compression will require the preparation of 12 standard concrete cylinders with 150 mm diameter and height of 300 mm. The concrete mix proportion is 1:2:4 by weight and water cement ratio is 6 gallons per bag of cement. One(1) bag cement is 40 kgs, one (1) gal is 3.785 liters. The specific gravity of cement is 3.15, sand 2.60 and gravel is 2.70. Determine the volume of concrete for 12 cylinders in m3: O 0.068 O 0.064 O 0.052 O 0.046
A box measuring 50 cm x 50 cm x 50 cm is filled to the top with dry coarse aggregate of mass 187.5 kg. The water absorption and specific gravity of the aggregate are 0.5% and 2.5, respectively. The maximum quantity of water (in kg, round off to 2 decimal places) required to fill the box completely is bris
Provide the concrete mix design for a large sewage reinforced concrete pipe. Maximum size of aggregates is 38 mm, and the required strength is 30 MPa after 7-days. Assume all other values. State the material types and the assumptions you are making.
The table below shows the properties of materials required to design a concrete mix. It is required to:a- Make a complete mix design.b- Express the proportions by volume for water, coarse aggregate, and fine aggregate, knowning that weight of 1 m3 gravel = 1760 kg/m3 and weight of 1 m3 sand = 1600 kg/m3.c- From the designed mix it is required to make a trial mix enough for six standard cubes (15 cm x 15 cm x 15 cm), six standard cylinders (d = 15 cm, h = 30 cm), and three standard beams (15 cm x 15 cm x 70 cm). what are the proportions of this mix? Using BSI Method only
*I E,90 KB/S H.W (4)-2nd cours... Concrete technology H.W (4) (A) Give reasons: Very early strength of concrete increases if temperature during placing and setting is increased. This is not the case for concrete strength after 7 days. (B) / Explain the following curve (use your own words (DO NOT COPY FROM THE LECTURE & DO NOT COPY FROM OTHER RESOURCES). 10000 Age at Test ePonded 8000 Hessian days 6000 bnded Hessian 4000 Ponded days Hessian Ty 2000 032 040 Woter / Cement Ratio 036 044
Estimate the approximate quantity of Cement, Fine aggregate, Coarse aggregate and Water, for five (5) Concrete Cylinders. If one finalized the ratio from ACI-211 Mix design for specified strength as (1:1.3:2) and W/C of 0.48. (Assume the given ratio is by weight)
Design a non-air-entrained concrete mix for a small job with a nominal maximum gravel size of 19 mm. Show the results as follows: a. mass of components to produce 2263 kg of concrete b. volumes of components to produce 1 m3 of concrete