7. The yoke-and-rod connection shown below is subjected to a tensile force of 5kN.Determine the minimum thickness of yoke if the bolt has a diameter of 25mm andthe bearing stress is limited to 12MPA.40 mm5 kN.30 mm25 mm5 kN

Answered: Image /qna-images/answer/e77d5eda-5c6b-4d71-b9b8-363769ef0d9b.jpg

Answered: 7. The yoke-and-rod connection shown…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

BOLTED/RIVETED CONNECTION: SITUATION: In the figure, assume that a 20-mm-diameter rivet joins the plates that are each 110 mm wide. The allowable stresses are 120 MPa for 20-mm Ø VE P bearing in the plate material and 60 MPa for shearing of rivet. 1. Determine the minimum thickness of each plate 2. Determine the largest average tensile stress in the plates if the rivet hole is 2mm larger than the rivet diameter. O 110 mm
A double angle ISA 75mm x 75mm x 8mm back- to-back welded to one side of a 12mm gussethave allowable stress 150MPa. Determine the allowable tensile load on the members and weldlength and overlap length of gusset plate.
Explain please
Pin diameter = 10 mm Gusset plate 15 kN Pin 50 mm Steel plate 6 mm thickness Column For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
3. A threaded rod and nut arrangement are guided with two washers, upper and lower washers tightened into a base plate. Considering that the base plate carries a load of 120 kN including its self-weight which is distributed equally: a. Determine the stress on the lower washers before the buts are tightened. b. Determine the stress int the upper washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. Determine the stress int the lower washer when the nuts are tightened so as to produce a tension of 5kN on the bolt. c. 44 mm Upper washer Base plate Lower washer 20 mm 22 mm 50 mm
Two 75mmx8mm A36 steel plates are welded in a 10mm gusset plate. Assume a weld thickness of 7.5mm and that of electrode used is E70. Determine the following: 1. Total Length of weld if P=300KN 2. Load P based on block shear if L1=85mm and L2=92mm. Neglect end returns P -2-75mmx8mm plates 10mm-thk L1 gusset plate L2 end returns
3) will upvote anyone who will answer
STRUCTURAL THEORY: USING PORTAL METHOD. Detailed computation. please
2. The figure shown is bolted with a diameter of 22mm. The inner plate material is 12mm x 315mm and the outer plate material is 9mm x 315mm. Assume hole diameter is 2mm larger than the bolt. T/2 T/2 F, = 345MPA, F, = 450MPA, F, = 207MPA, F, 1.2F, for bearing type connection. F, a friction type connection. = 117MPA for 45mm 75mm T/2 a. Determine the tensile capacity of the plates if it is a bearing type connection. b. Determine the tensile capacity of the plates if it is a friction type connection. c. Compute the minimum theoretical length of the lap if it is a bearing type connection. 75mm T/2 75mm 45mm A в А
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

7. The yoke-and-rod connection shown below is subjected to a tensile force of 5kN. Determine the minimum thickness of yoke if the bolt has a diameter of 25mm and the bearing stress is limited to 12MPA. 40 mm