7. Determine the reactions at the supports (4 and B). 18 kN 4.5 kN/m 600 kN m 9.0 m -6.0 m

Q: 25. ..s) Two circles, each of radius r, have their centers located at (0,2) and (0,3). Each is used…

A: As per honor code and answering guidelines I can  answer 1st question at a time.If you want other…

Q: A 3/4-in.-diameter hole is drilled in a piece of 1-in.-thick steel; the hole is then countersunk as…

A: The required volume of the given hole is obtained by rotating the area shown about the Y-axis.

Q: Nut 17.0 N 37° 25.0 cm

A: The text provides the following information:The force applied to the wrench is 17.0 NThe distance…

Q: /Wmsthe value of angle 0f andthevetueof02 -1000N

A: Calculated angles theta 1  and theta 2  .

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: Find Rotate the object about the given axis.

Q: find the center of the given shape

A:

Q: DRAN THE 1SOME TRG VIEW

A: Isometric view for the given orthographic views is drawn on the isometric grid paper. 1 Grid = 1…

Q: w of sine's when ( a= 100° , A=10.8 B=6

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: A 5 Find shear and bending moment diagrams

A:

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: Given data T = 320 N-m The allowable shear stress for the material is Tallow = 185 MPa.

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to calculate third view

Q: ده ))

A: The mass of each piece is m.

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: The distance between the corresponding point on the screw thread when measured parallel to the axis…

A: Create:  It is the peak edge of a screw thread, that connects the adjacent flanks at the top. Flank:…

Q: 1. Assume that the bracket shown is made from a homogenous (uniform) flat plate of negligible…

A: each segment with respective centroid is tabulated as below...............  SEGMENT A(mm2)…

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Draw the aligned sectional view of the following solid

A: According to the given data, there are two projection views. We need to find The sectional view as…

Q: Rotate the objects shown below by the indicated amount. Sketch the result in the space provided.…

A: the solution is provided in the picture attached below.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Locate the center of mass of the homogeneous solid block. 250 mm 200 mm 150 mm 100 mm 150 mm 150 mm…

A: Given:-  To Find:-  Center of mass of the homogenous solid block

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: The lower half of the moulding box is O a. Raiser O b. Drag O . Runner O d. cope

A: Given data Lower half of the moulding box is

Q: Two gears (A and B) are in mesh (they are interlocked) and both spin around their centers of…

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: What is the Neutral Axis?

A: The neutral axis is the fiber of the beam with no normal stress. When a beam is subjected to a…

Q: i need the answer quickly

A:

Q: What is the symmetrical axis?

A: Axis of symmetric.  Axis of Symmetry is a line that Split the figure into two symmetrical sections…

Q: In an experiment, an engineer wants to compare the torsional capacity of two shafts of the same…

A: Given data is

Q: please solve the centroidal  Ixc, centroidal Iyc, Ix and Iy of the attached figures

A:

Q: 1. Determine the cylinder displacement and engine displacement of an engine having six cylinders…

A: given data  bore diameter = 102 mm = 0.102m stroke length  = 120mm =0.120m number of cylinders =6…

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: Rc is -178.25 Ib. Why in the formula it's 17825 ?

A: The value of RC is represented as : Rc=-178,25 =-17825 lb The negative sign denote the direction…

Q: In a chain drive, the speed of the chain is not uniform and varies from a minimum  value to a…

A: The following step must be followed to come to the solution of the given problem:- Giver that:-…

Q: The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55…

A:

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to find three views.

Q: Q3: Draw the geometry shown in figure below . 88 38 12 719 -28 12 50

A: