7. Determine the effective slenderness ratio 8. Determine the allowable compressive stress 9. Determine the allowable load

Q: Describe method used to connect reinforcing grids to wall panel anchors.

A: The retaining wall system is a method for stabilizing an earthen wall and connecting reinforcing…

Q: Explain the difference between 1:50 and 1:100 in scale ruler Sketch it please to fully understand…

A: In architecture and civil drawings, different scale measurements are used in order to transfer the…

Q: SIZE : 300 mm. x 300 mm. MAIN BARS: 8-20 MM. Ø BARS. TIES: 3 TIES AT 10 MM. Ø 3 @ 50,5 @ 100, 7 @…

A: The drawing with proper details and dimensions are as given below:

Q: QUESTION 2 120 8 22- 14 - 40 70 56 34 44 R8 024 e 12 O8-2 Holes 64 26 34 22- STEPS: 56 1) Draw the…

A: For given isometric view, we identify the direction of the view. after identify that we can able to…

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Draw and label the standard symbols used in a horizontal stadia sight. Define each symbol used.

A:

Q: From the open compass traverse shown, if the forward bearing of line AB is N 75°30' E, compute the:…

A:

Q: load e line, determine distributed live la C m -4 m-

A:

Q: Two identical spheres weighing 100 KN each are placed in a container such that the lower sphere will…

A:

Q: 25 17.5 210 42.5 R23 R60 R50 R34 Scale 1:1

A:

Q: What is the importance of scaling the drawing to different paper size

A: Explanation:  Scaling in engineering drawings is very important aspect of any kind of drawing. To…

Q: Just draw the figure, if possible

A: Given data in question  Forward bearing  Back bearing Line Closed traverse To find out  Draw diagram…

Q: Choose the correct front view for the given drawing

A: i drawn rough sketch of front view   see it in below step

Q: Draw the orthographic views of the object shown.

A: Orthographic Projection: It is the most common method which represents three-dimensional objects. It…

Q: Determine (a) the x, y, and z components of the 750-N force, (b) the angles 0,, 0, and 0, that the…

A: first, draw the vertical and horizontal components Then calculate the scalar components The force…

Q: what lines should be drawn first when finished-line quality is being used

A: Brief concept- These given things are related to the drawing.

Q: Q2/ Draw by 2.5:1 scale the following shape. 4.00 2.50 001

A: Scale =Representative ValueTrue ValueSoAssuming that  the 2.5 unit in Diagram will be Drawn as 1…

Q: Draw the isometric view of the object shown.

A: Isometric drawing : Isometric drawing is the technical drawing that represents the three-dimensional…

Q: Given the Isometric View, draw the following: Top View Front View Right Side View Section View…

A: (Disclaimer: Since you have posted a question with multiple sub-parts, we will solve first three…

Q: Determine (a) the x. y, and z components of the 750-N force, (b) the angles , and e, that the force…

A: a) Fx=750 cos55° cos25° =389.88 N          ( Hint : Resolving 750 N to xz plane and resolving to…

Q: Determine the critical buckling load and stress of an 8" X 6" X 3/8" rectangular structural tube…

A:

Q: SM Ø HOLES 10M A12.5M "SM 125M BOM FRONT VIEW SIDE VIEW

A:

Q: Draw the Top, side, frotn view of the figure below

A:

Q: Problem 11 For a normally consolidated soils, a consolidated-undrained triaxial test was conducted…

A:

Q: Given the following isometric drawing, draw the top view, front view, and right side view

A:

Q: LINES Line 1-2 Line 2-3 Line 3-4 Line 4-1 BEARINGS N 78° 07" E $10° 26' E $ 81°53' W N 10°05' W…

A:

Q: Problem No.6. A log 0.30 m in diameter and 1.0 m long is thrown into the water such that its center…

A: The radius (r) is 0.30 m / 2 = 0.15 m.The length of the log is 1.0 m.Specific gravity 0.75Find depth…

Q: Answer g  Draw correct and complete figure

A:

Q: Create a hand drawing of the isometric view of this object to scale.

A: First Draw one missing view from the given two view by projecting lines.  A. After getting the…

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View,…

A: Hand made drawing are attached herewith of different views. Which will give you idea about different…

Q: SITUATION 2: The water table in soil deposit is 1 m below the ground surface. The soil above the…

A:

Q: What finished surfaces are available when selecting chalkboards?

A: The finish surfaces is based on material or paint we used for surfacing. there are certain options…

Q: (D) -

A: A sectional view in engineering drawing is a representation of an object as if it were cut by an…

Q: can you show detailed steps?

A:

Q: Problem 1: Given the following tabulated data for a closed traverse in which the lengths of CD and…

A:

Q: 3 in A axle lugwrench B tire The length AB for the lug wrench shown right is 12 inches. What is the…

A: Sy = 45 ksi d = 0.625 in

Q: Top, Front and Side view of this sketch.

A:

Q: Instructions: Redraw the objects in isometric orloblique views. Also, draw the three basic…

A:

Q: Process Control Schemes: Tutorial. Install appropriate control systems for the following tasks: (i)…

A: Process Control Schemes: (i) It represents the maintaining the process variable constant by suitable…

Q: Q2) Draw the top, front and side views of Figure 2 with a suitable scale. The dimensions need to be…

A: Given that....