7. A short rectangular reinforced column shown is to be part of a long span rigid frame and will be subjected to high bending moments combined with relatively low axial loads, causing bending about the strong axis. Steel bars are placed unsymmetrically as indicated in the figure. Consider the area displaced by compression bars. fe' = 27.6 MPa, fy = 414.7 MPa. Determine the (a) capacity of the column section considering the forces in the steel adjusted for concrete stress (b) plastic centroid of the section measured from the center of 36 mmø bars (c) eccentricity of the column load assuming the column load is applied at a distance of 300 mm from the center of the section towards the right side

7. A short rectangular reinforced column shown is to be part of a long span rigid frame and will be subjected to high bending moments combined with relatively low axial loads, causing bending about the strong axis. Steel bars are placed unsymmetrically as indicated in the figure. Consider the area displaced by compression bars. fe' = 27.6 MPa, fy = 414.7 MPa. Determine the (a) capacity of the column section considering the forces in the steel adjusted for concrete stress (b) plastic centroid of the section measured from the center of 36 mmø bars (c) eccentricity of the column load assuming the column load is applied at a distance of 300 mm from the center of the section towards the right side

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. An A36 Steel Cantilever Beam is shown below, also showing its cross section. Determine the following: Given the formula of the Maximum allowable bending stress of steel, fb = 0.66Fy. Where Fy is the Yield Stress of Steel. Where the bending stress for a beam is (fb) = Mc/I, where c is the distance of the centroid to the extreme most fiber of the beam (either top-most or bottom-most distance). Does the Steel fail under the loading given? Use Fy = 450 Mpa. Use the Moment in (a) and the moment of inertia in (c).
O FS = 2.4 O FS = 2.2 Consider a simple supported beam subjected to the load shown. The beam has a solid square cross-section with edge "a", and made of steel alloy having a yielding tensile and compressive strength of oy = 400 MPa. Determine its minimum required edge "a" for a factor of safety against yielding FS = 2.5. The area moment of inertia of that section about its neutral axis N.A. is INA = b.h³/12. of 3 kN 2 kN/m D 6 m + Select one: 5:37 PM 86°F Light rain ENG 6/18/2021 hp
The wide-flange pinned-end column shown in the figure carries two loads, a force acting at the centroid P₁ = 450kN and a force P₂ = 270kN acting at distance s = 100 mm, from the centroid. The column is an HE 240B shape with L = 4.2m, E = 200 GPa, and Oy = 290 MPa. (a) What is the maximum compressive stress in the column?
Problem- A mild steel bar of length 450 mm tapers uniformly. The diameters at the ends are 36 mm and 18 mm, respectively. An axial load of 12kN is applied on the bar. E= 2 × 10 N/mm². The elongation of the bar will be
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
3. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc-20.70 MPa. In checking whether steel yields or not, the value of "fs" is__ _MPa. 1644.056 1302.491 1935.087 2402.455 O2735.802 O 3014.642 Other:
Consider the truss shown in (Figure 1). Suppose that F = 12 kN. gure B C D 12 m, 6 @ 2 m E F 3 m Part A Determine the force in member CD and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCD = Submit Part B FCJ = Submit __ Part C μA Value Request Answer Determine the force in member CJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. μA Value Units Request Answer ? Units ? Determine the force in member KJ and state if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension.
The initial compressive force of a steel column can be determined by Euler's buckling formula. The column has the following properties: A = 9484 mm² Fy=345 MPa 1x = 164 x 100 mm4 ly = 23 x 105 mm² Proportional limit, f = 290 MPa The x-axis has an unbraced length of 10 m which is pinned at the top and fixed at the bottom with an k = 0.70. The y-axis has unbraced length of 5 m due to the bracing at the mid-height. Which of the following most nearly gives the axial force in the boom? Select the correct response: 104.62 kN 43.33 kN 94.75 kN 38.14 kN E = 200 GPa
Determine the polar moment of inertia for brass sleeve and steel shaft.
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁