7. A 3.3V 1N4728A Zener has a reverse breakdown voltage, -V₂ = -3.3 V, and a Zener 'knee' current, -Izx = -1 mA. In contrast, the 1N5226 Zener has the same reverse breakdown voltage, - Vz= -3.3 V, but a Zener 'knee' current, -Izx = -20 mA. a. In the circuit below, find the maximum resistance, R, that enables the 1N4728A Zener to regulate the voltage at 3.3 V. b. To see the effect of different Zener diodes, if a 1N5226 is used instead in the circuit below, find the maximum resistance, R, that enables the 1N5226 Zener to regulate the voltage at 3.3 V. 5V 1N4728A R Vout

7. A 3.3V 1N4728A Zener has a reverse breakdown voltage, -V₂ = -3.3 V, and a Zener 'knee' current, -Izx = -1 mA. In contrast, the 1N5226 Zener has the same reverse breakdown voltage, - Vz= -3.3 V, but a Zener 'knee' current, -Izx = -20 mA. a. In the circuit below, find the maximum resistance, R, that enables the 1N4728A Zener to regulate the voltage at 3.3 V. b. To see the effect of different Zener diodes, if a 1N5226 is used instead in the circuit below, find the maximum resistance, R, that enables the 1N5226 Zener to regulate the voltage at 3.3 V. 5V 1N4728A R Vout

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Good day!Question: State the principle of reactance tube modulator? Thanks
Electrical Engineering _ Energy Conversion Systems pls find the question by using computer line. pls find fast.
Which of the following distribution systems would you select for a medical research campus? A) Primary selective system. C) Secondary loop system. B) Distributed radial system. D) Primary and secondary loop system. Authoritative rules for electrical design and installation are contained in which of the following 7) documents? A) ASHRAE Handbook of Fundamentals. B) NFPA 101. C) NEC. The illumination from a point source 4 ft. above a surface is 100 foot-candles, and the surface is normal to the source. What will be the illumination level if the surface is tilted 45°? A) 50 foot-candles. B) 100 foot-candles. C) 71 foot-candles. Which of the following lamp types is generally the most energy efficient? A) Incandescent. C) High intensity discharge. B) LED. D) Fluorescent.
NOTES: solve by using computer line.
What is the meaning of the acronym, XLPE? O A. CROSS-LINED POLYETHYL EQUIPMENT O B. CROSS-LINKED POLYETHYLENE O C. EXTRA LOW POLYESTER EQUIPMENT O D. EXTREMELY LINED POLYMER EXTRUSION
SUBJECT: INDUSTRIAL ELECTRONICS TOPIC: Power Supply Using LM 317 & LM337 NOTE: ANSWER THE FOLLOWING QUESTIONS AND EXPLAIN AND EXPOUND YOUR ANSWER! MAKE SURE THE ANSWER IS CORRECT TO RATE YOU HIGHLY FOR THE ANSWER. ANSWER THE TABLE AND OTHER QUESTIONS. THANK YOU! answer with correct, PLEASE FOLLOW INSTRUCTIONS ANSWER IT IN CORRECT & Explain THANKS Make a (3) titles about this project: A. B. C. Make abstract about this project: ABSTRACT - [ is a self-contained, short, and powerful statement that describes a larger work. Abstracts cannot contain equations, figures, or tables.] Make an introduction about this project that contains the (1) Background of the Project (2) Objective of the Project, (3) Scope and Limitation of the Project INTRODUCTION
4. What is the significance of Power factor? Explain it with the help of Power Triangle. Refer ProQuest/Internet, Type and submit the answer not less than 200 words in Turnitin Assignment link in Moodle. Properly mention the ProQuest Link/reference website in the submission)
Please answer ASAP for like this please Asap for like this please... Please
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Enumerate 5 or more home safety tips to avoid short circuits.
In relation to ”smart grid”, discuss the attributes that make the gridsmart.