7. A 3 phase, Y connected generator has balanced voltages such that Va It supplies a 3-phase balanced, Y-connected load with per phase impedance of 8 + j6 Q. The impedance of line connecting the generator to the load is 0.1 + j1.0 Q per phase. Assuming a phase sequence of a,b,c, calculate: (i) Currents in all phases. (ii) Neutral current (iii) Generator and load phase and line voltage magnitudes. = 120230°.

7. A 3 phase, Y connected generator has balanced voltages such that Va It supplies a 3-phase balanced, Y-connected load with per phase impedance of 8 + j6 Q. The impedance of line connecting the generator to the load is 0.1 + j1.0 Q per phase. Assuming a phase sequence of a,b,c, calculate: (i) Currents in all phases. (ii) Neutral current (iii) Generator and load phase and line voltage magnitudes. = 120230°.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power Transmission and Distribution Discuss the advantages and disadvantages of single-phase and three-phase system
1.) A 6 pole, 75 Hz, 240 V, Y-connected, 3-phase generator has a synchronous reactance of 2 ohms and negligible resistance. The balanced three-phase load draws 220 kVAR at 0.90 lagging pf at 240 V. e. Solve for the voltage regulation. f. What is the current drawn by the load per phase? g. Compute the power developed in the armature per phase. h. At a total of 20kW of losses, what is the efficiency of the alternator?
The shown distribution network is to supply two factories A & B with load curves indicated. Assume that both factories have a lagging power factor of 0.8 . a) Select the required sizes of transformers for both factories such that in the case of a failure in one transformer the overload on the remaining ones should not exceed 15% . b) Select the required sizes of fuses to be installed at both sides of transformers. c) Calculate the annual energy losses in transformers of factory A. Assuming that transformers are in operation continuously . d) Select the required size of the 11KV. XLPE cables for the distribution network , if cables are to be laid direct in ground with тахітит ground temperature of 30° С. e) Calculate the annual energy losses in cables of section SA . S 2 Km A 3 Km 11/0.4 KV Trans. 11/0.4 KV Trans. Factory A PF = 0.8 lag. Factory B PF = 0.8 lag. | S (KVA) 500 |S (KVA) 500 400 400 300 300 200 200 100 100 Time (hr) 24 Time (hr) 24 6. 12 18 12 18 Load curve of Factory (A)…
An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an athree-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. Determine a) linecurrent and line voltages with its degrees, b)Draw the current –voltage phasor diagram c) and the power generated inthe line quantities of the alternator.
Qa1. The three phases of a generator can be connected in either delia (D) or wye (Y) connection. List two advantages of three phase system over a single phase system. Also write mathematical relationship between the phase voltage and the ine voltage, and the phase current and the line current for both delia (D) and wye (Y) connections. Please answer in typing format please..
i need the answer quickly
In a three-phase system the per-unit phase voltages are 100° , Vôn = 0.8Z180° Van 0.920° , Von = 0.92 - а What are the per-unit symmetrical components V0) and V)? Express in polar notation.
19. Two single phase generators operating in parallel have no-loads emfs of E₁ = 24020° V and E₂ = 240/10° V and respective synchronous reactance of Xs1 =j2.5 ohms and Xs2 = j3.1 ohms. Resistances are neglected. The common load is purely resistance of 10 ohms. Find the common terminal voltage in volts. d. 232.65 V d. 6.05, 17.8 A d. 4,985 W a. 236.98 V 20. Referring to problem 19, find a. 6, 17.9 A 21. Referring to problem 19, find a. 4,464 W b. 234.76 V c. 240 V the current of each generator in amperes b. 5.82, 18 A c. 6.34, 17.5 A the total power in watts b. 5,792 W c. 5,616 W
None
Number 17
When this generator is connected to a 13.8 kV distribution feeder of negligible impedanceand operates at an output power of 8.75 MW at 0.9 power factor lagging, work out the field current, the reactive-power output, and the load angle for this operating condition.
Referring to the circuit shown in Figure 1 below, solve the following problems: - i) Calculate the total impedance, ZT. ii) Determine the total current, Ir supplied by the generator iii) Determine the value of current at load impedance, I1, I2 and I3. iv) Calculate total real power, PT and reactive power, Qr supplied by the generator. v) Draw a power triangle of this circuit vi) Calculate the power factor of this circuit.