7) Which of the following types of stresses are induced in the stretch forming process? Tensile only. Compressive only. A combination of tensile and compressive stresses. A combination of tensile, compressive and shear stresses

Q: d) If a material of a component has a youngs modulus of elasticity of 800 GPa, what strain will be…

A: Given data: E=800 GPaσ=5 MPa Need to determine the strain.

Q: Distinguish between simple and indirect shear stress?

A: Simple shear stress also known as direct shear stress is the shear stress developed due to a…

Q: Why do the Ductile materials fail in shear?

A: Ductile materials are the materials which goes plastic deformation before the fracture. When any…

Q: scuss the concept of stresses? State the properties could be drawn from the stress strain diagrams

A: when load is applied on a member , by nature it will try to deform the member. the material will try…

Q: Why is it important to find the absolute maximum shear stress in the material when it is subjected…

A: Shear stress: It is the force imposed per unit area in a body that cause deformation of a material…

Q: engineering  and  true  stress strain curves for shear are similar guess

A: Given:

Q: Do ductile materials fail in shear?

A: The type of materials that undergo considerable plastic deformation before fracture are known as…

Q: What happens if the principal stresses at a critical point in the material?

A: First, define the critical point. Critical points are those points in the given plane where the…

Q: 1. What is the difference between direct and shear stress?

A:

Q: Define the term transverse shear?

A: The shear stress which occurs due to bending moments in a body is known as the Transverse shear.

Q: (SI Units) In a tensile test on a steel specimen, true strain = 0.11 at a stress of 245 MPa. When…

A:

Q: Give an example of the single shear failure?

A: Shear is caused by the action of two opposite and equal forces acting on a material. If the two…

Q: If a material of component has a tensile modulus elasticity of 300 GPa, what strain will be produced…

A:

Q: Give an example of the Absolute Maximum Shear Strain?

A:

Q: What is the unit of strain?

A:

Q: What is the relationship between moment and shear?

A: The shear force and bending moment are related to each other through a differential equation. The…

Q: What is the permanent strain?

A: Strain: When a force is applied to any system, they deform based on the applied force. The…

Q: Problem 5. Chapter 17 Material Behavior Annealed low-carbon steel has a flow curve with strength…

A:

Q: What do the normal strains cause?

A:

Q: How is the Strain actually measured?

A: Before explaining the measurement of strain, let's first understand the strain. Strain is basically…

Q: Distinguish between the Normal and Shear Stress Components?

A: Normal and shear stress components are distinguished by their direction with respect to the area on…

Q: The maximum stress a material can with stand before failing is termed.... O O the elastic limit the…

A: The maximum stress a material can with stand before failing is termed... Answer: the ultimate…

Q: 3) A tensile test is performed to determine the parameters strength constant C and strain- rate…

A:

Q: What are principal stresses?

A: The highest and the lowest value of the normal stress acting at a point is known as the principal…

Q: 5) Draw the stress-strain curve and gives the stress and strain equations for both Engineering and…

A:

Q: 27d)  If a material of a component has a youngs modulus of elasticity of 500 GPa, what strain will…

A:

Q: Write out the most general expression for shear strain along a single axis resulting from all…

A: Given question: Write out the most general expression for shear strain along a single axis resulting…

Q: - In a rolling process, the state of stress of the material undergoing deformation is (a) pure…

A: In a rolling process, the state of stress of the material undergoing deformation is Answer: (c)…

Q: What is the linear variation in shear stress along any radial line?

A: For a linear-elastic material, the shear stress varies linearly with shear strain.

Q: Between  1. Nominal (engineering) stress and true stress and 2. True strain and engineering strain…

A:

Q: What are the principal strains?

A: Principal Strain: Maximum and minimum normal strain possible for a specific point on a structural…