7) Two disks A and B weigh 2 lb and 5 lb, respectively. If they are sliding on the smooth horizontal plane with the velocities shown, determine their velocities just after impact. The coefficient of restitution between the disks is e = 0.6. V = ?,0, = ?,V = ?,0, = ?, 10 ft/s 5 ft/s 30° A 45°

Q: what is 6 to 10 po?

A:

Q: Based on the system shown in Figure 1, develop the position equations from your fixed datum lines,…

A:

Q: resolve solution

A:

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: QI Define five of the following with sketch. 1-Taper turning 2- Light alloys 3- AA2024 4- Rolling 5-…

A: Taper turning is a turning technique in which the cutting tool travels at an angle to the…

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: Water falls vertically downward from an open faucet with an initial velocity of 47 cm/s. If the…

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: can you resolve and draw the fbd

A: Freebody diagram of the cut section:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: Tät-/e205+(17-78 2.

A: Given Data⇒a↦=202+17.782

Q: 200 mm В

A:

Q: D raio s.f.D and B.M.

A:

Q: Q1: Find the angle of the force? 250 Ib 110 Ib 25 140 Ibk 40° 90 Ib 170 Ib

A:

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: Using the method of joints, determine the force in each member of the truss shown. State whether…

A:

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: Given : Mass of Gears A and B = 2.4 kgs Mass of Gear C = 12 kgs Gears A and B's radius of gyration =…

A:

Q: Choose three types of Reuleaux lower pairs, and answer the following, F.1 Write down their names?…

A:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: continue the question

A: Given: (d) The dimension of the plate: →A=1.2m*1.2m Because the distance of the center of gravity of…

Q: If a = 9 in., locate the distance to the centroid of the member's cross-sectional area. (Figure 1)…

A: Draw the given diagram.

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.