7) The homogeneity of the chloride level in a water sample from a lake was tested by an analyst. Below are the concentration in parts per million (ppm) of Cl: 27.32, 27.22, 27.21, 27.24, 27.20 i. Determine the mean and median. ii. Calculate the confidence limit at 90%. iii. Identify a possible outlier and use the Q-test to determine whether it can be retained or rejected at 90% confidence level

7) The homogeneity of the chloride level in a water sample from a lake was tested by an analyst. Below are the concentration in parts per million (ppm) of Cl: 27.32, 27.22, 27.21, 27.24, 27.20 i. Determine the mean and median. ii. Calculate the confidence limit at 90%. iii. Identify a possible outlier and use the Q-test to determine whether it can be retained or rejected at 90% confidence level

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A dilution of benzene in methanol is made by placing 1.5 mL benzene (density of benzene is 0.879 g/mL and its mol. Wt. is 78.1) in a 100-mL volumetric flask and brining to volume with methanol. What is the concentration of benzene in the solution in mg/L In ppml
(V,M, = V,M,) %3D 2 2 .1L of commercial grade hydrochloric acid is added to water to bring the total volume of the solution to 0.82L. What is the resulting concentration if commercial grade hydrochloric acid has a molarity of 12.4 M? O 1.51 M O 1.02 M O 6.60 M O 10.2 M hp % & %23 4. 2 t e f S d' w/
A compound “X” is regulated by health Canada at 2 ug/L in drinking water (maximum allowable concentration). What will be the minimum cut-off level of your analytical method to analyze that compound “X”? How do you determine the cut-off level of your method?
Q6. The following set of millimolarities were obtained when standardizing a solution: 10.67, 10.71, 10.66, and 10.45. One value appears suspect. Using Q test determine if it can be ascribed to accidental error, at the 90% confidence level.
Six 50.0 ml volumetric flask 1 through 6 are labeled. 10.00 ml of 2.00 x 10-1 M Fe(NO3)3 solution was then pipet into each volumetric flask. A 1.00,2.00,3.00,4.00 and 5.00ml of 2.00 x 10-3M NaSCN solution was then pipetted to flask 2 through 6 respectively. A sufficient amount of 0.10 M nitric acid was then added to each flask to make each a total volume of 50.00ml. Hint M1V1=M2V2 a)what would be the concentration of Fe(NO3)3 in 0.10M HNO3? b)what would be the concentration of NaSCN in 0.10M HNO3?
5a.
A 25mL volumetric pipet is used to deliver a sample of the stock solution marked “0.6000M X2SO4” into a 100mL volumetric flask. Distilled water is added to the flask until it is about 3/4thfull, the solution is mixed well, then more water is added to fill it up to the calibration mark, then it is mixed again. Calculate the concentration of X+ion in the dilute solution made above.
Using recrystallization techniques, a student attempts to purify 0.50 g of compound H. Based on the solubility of H in the chosen solvent at collection temperature, the maximum percent recovery is 82%. The student obtains 0.396 g of purified crystals. What is their percent recovery? Group of answer choices 41% 64% 79% 82% 97% none of these
4
A student dissolved 20 mg of caffeine in 20 mL of water. The student carried out two extractions using 20 mL of dichloromethane in each one. Caffeine solubility in water: 2.17 g / 100 mL at 25 ° C Caffeine solubility in dichloromethane: 10.0 g / 100 mL at 25 ° C Present the calculations in detail below. A. Determine the distribution coefficient. b. Determine the amount of caffeine obtained in the first extraction. C. Determine the amount of caffeine obtained in the second extraction. 77 D. Determine the total amount of caffeine extracted during the entire process. and E.Determine the percent recovery.
3a.
Note: The explanation of this work would be we did a work on the process of preparing diverse solution sets and regarding that these are the following sets of questions. PART: 2 What happens to the solution's concentration when you add more solute to the same volume of solvent? How to raise the concentration of an aqueous solution? When is the ppm concentration applied? What do you conclude from this lab? Was your hypothesis confirmed or not? Explain your answer.