7- Prove that (1 poise = dyne.sec

Q: 1081. An auto, equipped with only front wheel brakes, has a wheelbase of 120 in. with its c.g.…

A: The value of friction must be maximum for the minimum stopping distance.…

Q: Two boys riding in bicycles A and B respectively travels towards each other. When the distance…

A:

Q: 1078. The 240-lb body in Fig. P-1078 is supported by wheels at B which roll freely without friction…

A: Given data as per question Mass of body =240 lb coficient of friction =0.4

Q: If the speed of the crate at A is 15 ft/s, which is increasing at a rate v = 3 ft/s², determine the…

A:

Q: 4.18 What is the composition, in atom percent, of an alloy that contains 44.5 lbm of Ag, 83.7 lb,m…

A: Given data:         mass of Ag= MAG= 44.5 lbm         mass of Au= MAU = 83.7 lbm         mass of Cu…

Q: Answer Fig. P3.59 and P3.60 0.2 m 0.7 m 0.6 m 0.9 m 0.4 m 0.3 m C E 0.9 m 0.6 m B F 0.35 m 0.4 m 0.6…

A:

Q: flow by 15", as shown in the fīgure flow are 40 kPa and 263 K. respec

A:

Q: An Otto cycle engine is operating on the following conditions: The pressure and temperature at the…

A: As per given question  P1=150 kpa T1=300k Maximum condition  P3=5100kpa T3=2900 k We have to find…

Q: A stone is thrown vertically upward from the ground with a velocity of 300ft/s. How long must one…

A:

Q: A vacuum gauge mounted on a condenser reads 0.56 m Hg. What is the absolute pressure in the…

A:

Q: Find The curevature points A,B,C,D form least to greatest

A:

Q: (a) Which component of the horizontal axis wind turbine can be considered as the brain of the…

A: In the horizontal axis turbine, the component considered as the wind turbine's brain is termed as…

Q: A liquid is being pumped through a pipe whose diameter is 15mm. At the operating temperature and…

A:

Q: Determine P and RA

A:

Q: A vacuum gauge mounted on a condenser reads 66 cm Hg. What is the absolute pressure in the condenser…

A:

Q: (F-Odd) When the motion of the particle is expressed as a = 6 · 2t, a is in m/s² . The particle is…

A:

Q: 1077. The uniform block shown in Fig. P-1077 weighs 200 lb. It is pulled up the 300 lb. Determine…

A: Given: load P =300lb weight W=200lb To Find: Max and min d

Q: What is the weight in dynes of 12 oz of salt? Local g is 9.55 mps?.

A:

Q: Determine the time during which the satellite is above the horizon for an observer located at the…

A:

Q: A 10-kg steel wheel shown in Fig. 8–26a has a radius of 100 mm and rests on an inclined plane made…

A:

Q: Fill in the blanks: Compute the difference in pressure (Pa-PR) if pipe A contains oil with sg = 0.92…

A: To find PA-PB Specific gravity of oil =0.92 density of mercury = 13.6*10^3

Q: Find the. Force

A: Given  The magnitude of Force F1= 1000 N                                        F2=880 N

Q: PROVE THAT THE ANGLE IS 30° BY LAWS OF CONGRUENCY

A:

Q: 3.35 The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a…

A:

Q: team is generated at 4.0 MPa and 440°C and condensation ccurs at 0.15 MPa. (a) Considering that…

A:

Q: A centrifuge bowl is to separate two immiscible liquids, one with SG 1.1 and the other with SG 0.9.…

A:

Q: A force of magnitude 1000 N passes from B (4,4,6) m to C (-4, 1,1) m. Calculate moment o this force…

A: Write the vector of BC. BC=C-B=-4,1,1-4,4,6=-8i-3j-5k   Calculate the unit vector of BC.…

Q: Prove that CIpoise = 0.1 dyne.sec cm2

A: Poise: The poise is the unit of dynamic viscosity. The unit of the viscosity is N·sm2 in the SI…

Q: Problem 5.1.6 5.1.6 WP The pump shown in Fig. P5.1.6 produces a steady flow of 10 gal/s through the…

A:

Q: Determine the forces in members FE, ED and EB both a). by the Method of Joints and b). by the Method…

A:

Q: Using your answer from the problem above, find the dimensions of I in the equation 1²EI Рer L2 This…

A: Given: Pcr=π2EIL2

Q: APPROXIMATE ANALYSIS OF INDETERMINATE STRUCTURES S T Solve the reactions at the support and the…

A: Please find the solution below

Q: For the given state of stress, determine the normal and shearing stresses after the element shown…

A: Given Stress at X = 0 MPa Stress at Y = 56 MPa Shear stress XY = 35 MPa To find Normal and shear…

Q: 4/1 Determine the force in each member of the simple equilateral truss. Ans. AB = 736 N T, AC = 368…

A:

Q: convert (3.75 mm.kg)/(3ft).

A: Solution:   Conversion in SI unit is:

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.