7 ft A 4 ft- d 800 lb B W The framework shown is supported by the member AB which rests on the smooth floor. When loaded, the pressure distribution on AB is linear as shown. Determine the length d of member AB and the pressure intensity w for this case.

7 ft A 4 ft- d 800 lb B W The framework shown is supported by the member AB which rests on the smooth floor. When loaded, the pressure distribution on AB is linear as shown. Determine the length d of member AB and the pressure intensity w for this case.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. Use E = 200 GPa B 60 kN 2 m 40 kN E F1m--1m--1 m--1m-
Please answer part a b c
P1=58kN P2=80kN
answer problem 3 only
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.45 in. Aluminum rod (2) has an elastic modulus of E2 = 10,000 ksi and a diameter of d2 = 0.75in. Aluminum rod (3) has a diameter of d3 = 0.95in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L1 = 6 ft, L2 = 8 ft, and L3 = 3 ft.FIND: (a) Calculate the cross-sectional areas of the three rods.(b) For a factor of safety of 1.9, calculate the allowable stresses in the bronze and the aluminum rods. (c) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship…
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 2.8 in.?. Assume a = 2.75 ft and b = 3.30 ft. If the normal stress in each member must not exceed 55 ksi, determine the maximum load Pmax that may be supported by the structure. E a В Answer: Pmax kips
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.45 in. Aluminum rod (2) has an elastic modulus of E2 = 10,000 ksi and a diameter of d2 = 0.85in. Aluminum rod (3) has a diameter of d3 = 1.00in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L1 = 6 ft, L2 = 8 ft, and L3 = 3 ft.(a) Determine the magnitude of load P that can safely be applied to the structure if a minimum factor of safety of 1.7 is required.(b) Determine the deflection of point D for the load determined in part (a).(c) The pin used at B has an ultimate shear strength of 59 ksi. If a factor of safety of 3.1 is required for this double shear pin connection, determine the minimum pin diameter that can be used at B.
The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
Axial loads are applied to the compound rods that composed of an aluminum segment rigidlyconnected between steel and bronze segments. If P = 25 kN, determine the following: a. Stress in the bronze segment. b. Stress in the aluminum segment. c. Stress in the steel segment.
The shaft is made of A992 steel. It has a diameter of 0.7 in. and is supported by bearings at A and D, which allow free rotation. The shear modulus of elasticity for the material is 11 × 10³ ksi. 2 ft < 5 of 7 Part A B 2.5 ft > 60 lb-ft C 3 ft O 60 lb-ft
Pls help