7-48 Water vapor enters a compressor at 35 kPa and 160°C and leaves at 300 kPa with the same specific entropy as at the inlet. What are the temperature and the specific enthalpy of water at the compressor exit? 300 kPa Steam compressor 35 kPa 160°C Wo out

Q: What are the types boiling occur in evaporator? Define them

A: Define : the type of boiling occur in evaporator

Q: A tank of 0.1 m' volume is connected to a high-pressure air line; both line and tank are initially…

A:

Q: what is the types of industrial compressors, write summary and work mehod of each type?

A: Compressors:- compressors are used to compress the air or any fluid to raise the pressure of that…

Q: Question 11: A non-flat plate is placed inside a wind tunnel where the air velocity in the test…

A:

Q: Air from a line at 12 MPa, 15 deg. Celsius, flows into a 500 L rigid tank that initially contained…

A:

Q: i. An aircraft is flying at a speed of 500 ft/s an altitude of 20,000 ft, where the atmospheric…

A: GIvenspeed of air craft V=500ft/s=152.4m/sAltitude h=20000ftAtmoshperic temeperature…

Q: . Assess the different types of industrial compressor and identify justifiable applications for each…

A: The three most commonly used air compressors are reciprocating, rotational screw, and centrifugal.…

Q: ortunities to recogni at these en

A: given:

Q: Give a concise introduction on Douglass pressurized reservoirs.

A: DOUGLASS PRESSURIZED RESERVOIR :- Douglass pressurized reservoir is a tank which has immense…

Q: Energy-saving opportunities are present everywhere in compressed air systems, it just takes minimal…

A:

Q: 2. A. Design a theoretical nozzle in order to expand isentropically superheated steam (P₁ = 280…

A:

Q: ..Equation for Law of conservation of mass and energy for a nozzle

A: Law of conservation of mass (For nozzle) The mass is conserved during the process, the mass of fluid…

Q: b) How to Investigate the variation of air flow rate with compressor ratio (With Intercooler)?

A: Air compressors are the device which is used to increase the pressure of air by applying for dynamic…

Q: Deriye an expres sion for velocity

A: Consider a nozzle as shown below,

Q: Apply the steady flow energy equation to nozzle, compressor, turbine, boiler, and mixing  chamber.

A: During steady flow-process, the total energy of a control volume remain constant i.e., ECV=constant…

Q: 1. define the cutfof ratio and the compression ratio     2. air is compressed at a constant…

A: Define cutoff ratio and compression ratio

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

A:

Q: Hext 5 questions are inter-related. A jet fighter is flying at 40.000 ft at M-0.9. The inlet presue…

A:

Q: An engine has an inlet stagnation condition of 300 bar and oxygen make up the products of combustion…

A:

Q: Q. (A) Fill in the Blanks 1. The leakage in balanced flow control valve is 2. All pressure relief…

A: In this problem, we have to fill the suitable word or arrangement of words.

Q: ck work ratio, Thermal Efficiency (% No Description Pressure ratio=B Ratio…

A: Given, T1 = 27oC = 273 + 27 = 300 K P1 = 100 kPa Compressor Ratio1  = 7 Compressor Ratio2  = 12 From…

Q: Which one of the following is true to reduce the work input to a compressor O increase the pressure…

A:

Q: Define the overall pressure ratio of a two stage compressor? A- It is the ratio of isothermal power…

A: For a gas turbine the overall pressure ratio for any two stage compressor is defined as the "ratio…

Q: To determine: The type of change in suction pressure when evaporator experiences a heat-load…

A: Given data : Suction pressure  Heat load increase

Q: How can we calculate pressure drop through a baghouse at a given gas flow rate?

A: Pressure Drop

Q: Explain the difference between back pressure and exit pressure (in context of a gas flowing through…

A: Back pressure Back pressure is a resistance or force opposing the desired flow of fluid through…

Q: 2.) Steam with enthalpy of 3350 kJ/kg enters a nozzle at a velocity of 80 m/sec. Find the velocity…

A: This is the very basic numerical of thermodynamics and used concept is  Steady flow energy equation.

Q: recognize where energy can be saved. hese energy savings can be maintain air systems or application…

A: Given

Q: too lean mixture is supplied to the engine and may be caused in:

A:

Q: Please add units.

A: Unit: It is used as a measure to quantify the quantity identical kind. Every physical quantity has…

Q: 9. A mixture of water and steam flowing out of a vent at 200 psia and quality of 0.27. Find the void…

A: Given DataP=200psiax=0.27

Q: 2. Fuel in Combustion chamber Turbine Net Power Air in Out Axial compressor Centrifugal compressor…

A:

Q: Discuss on why a need of improvement of a single stage compressor system is there and what are the…

A:

Q: Drive an expression for the loss in laminar flow.

A:

Q: Fixed geometry jet engine inlet is not feasible for very low supersonic Mach no.

A: In order to achieve optimal operational efficiency, the air flow into the compressor should be…

Q: A pipe can fill a swimming pool in 15 hrs. If a second pipe is open, the two pipes together can fill…

A: Given Data: Time required by first pipe, t=15 hours Time required by both pipes, t=5 hours

Q: Describe the factors influencing the flow rate and pressure in pressurized flow systems, such as…

A: The relationship between flow rate and pressure is strong in pressurized flow systems, such as pipes…

Q: Derive an eeporession for Gysoscopic Couple

A: The answer is given in next step

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.