*6–64. Draw the influence line for the force in member IH of the bridge truss. Determine the maximum force (tension or compression) that can be developed in this member due to a 72-k truck having the wheel loads shown. Assume the truck can travel in either direction along the center of the deck, so that half its load is transferred to each of the two side trusses. Also assume the members are pin connected at the gusset plates. 32 k 32 k 8 k I H G Ț10 ft F110 ft A KE LE ME B |C D |E 25 ft 15 ft 20 ft ' 20 ft ' 20 ft' 20 ft ' 20 ft Prob. 6–64

*6–64. Draw the influence line for the force in member IH of the bridge truss. Determine the maximum force (tension or compression) that can be developed in this member due to a 72-k truck having the wheel loads shown. Assume the truck can travel in either direction along the center of the deck, so that half its load is transferred to each of the two side trusses. Also assume the members are pin connected at the gusset plates. 32 k 32 k 8 k I H G Ț10 ft F110 ft A KE LE ME B |C D |E 25 ft 15 ft 20 ft ' 20 ft ' 20 ft' 20 ft ' 20 ft Prob. 6–64

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the resultant force at pins A, B, and C on the three- member frame. 200 N/m 60° C 2 m Prob. 6-72 800 N 2m
HW Determine the resultant force at pins A, B, and C on the threo-member frame. 200 N/m
2
(1) The beam AB will fail if the maximum internal moment at D reaches 800 Nm or the normal force in member BC becomes 1500 N. Determine the largest load w it can support. (Supports A & C are pinned and there is an internal hinge at B) 4 m D 4 m W B -4 m- 3 m C
2-2 A 100-N force is applied at end C of the rod as shown. c) Assess the effect of the angle being varied from 0° to 360° to the moment of the 100-N force about point A. [b) (i) MA=0 N-m; (ii) MA=-24k N-m; (iii) MA=-12k N.m] 2-3 A 600-N force is applied on end D of the bent rod as shown. c) Assess the effect of the angle being varied from 0° to 180° to the moment of the 600-N force about point A. [b) (i) MA= 180 N-m; (ii) MA= - 480k N-m; (iii) MA= 180k N-m; (iv) MA=- 432k N.m] Figure IA Figure 150 mm P2-2 600 N 50 cm B P2-3 90 mm 0 000 B 30 cm C 100 N 30 cm
The beam supports a uniform dead load of 500 lb>ft and a single live concentrated force of 5 k. Determine (a) the maximum negative moment at E, and (b) the maximum positive shear at E. Assume the support at D is a pin, A and C are rollers, and B is a pin. A B C D E -9 ft- -9 ft- -9 ft- 06 PROB 023 -9 ft-
Construct the influence lines of each truss member.
Problem 2 The truss shown carries the following uniform live load and concentrated live load. E G 3 m A B C D 3 @ 4 m 12 m LOAD W(LL) P(LL) SET 1 (1,2,3,4,5) 20 90 Draw the necessary influence line diagrams and calculate the following: 8. Maximum axial force on EF. (