650 kg 1.2 m 140 kg

Q: The figure shows an impact tester used in studying material response to shock loads. The 67-lb…

A:

Q: P13.147 The 700 kg hammer of a drop hammer pile driver falls from a height of 1.5 m onto the top of…

A:

Q: Block A supporting another block B is pulled along a rough horizontal plane by a horizontal force P.…

A:

Q: Parvinbhai

A: The objective of the question is to find the maximum acceleration of the race car such that the…

Q: When the 11-lb block A is released from rest it lifts the two 15-lb weights B and C. Neglect the…

A:

Q: Problem 3: Calculate the horizontal velocity v with which the 48-lb carriage must strike the spring…

A: The weight of the carriage,

Q: the following most nearly gives the force P to cause the impending motion of block B to the right.…

A:

Q: Learning Goal: The two blocks shown have masses of mA = 43 kg and mp=78 kg. The coefficient of…

A: Given: mA = 43 kg mB = 78 kg s = 2.5m angle = 35 degree Answers: NA = 345.54 N vB = 4.43 m/s

Q: Determine the force P for impending sliding motion of block A 30° IMPENDING MOTION B 50lb ALUMINUM A…

A:

Q: If the 55-kg crate starts from rest and travels a distance of 8 m up the plane in 6 s, determine the…

A: Solution: Given Data: m=55 kgs=8 mt=6 sμk=0.27u=0   To Find: Magnitude of force P acting on the…

Q: Q.1) A 50 kg block is dropped from a height of 2 m onto the the 20 kg pan of a spring scale.…

A: Given data: The mass of block is M = 50 kg. The height from which the block is dropped is h = 2 m.…

Q: The crate, which has a mass of 170 kg, is subjected to the action of the two forces. (Figure 1) Part…

A: Given: A crate having mass of 170 kg is subjected to action of two forces as shown below.…

Q: :--1 manning 1. Define both the coefficients of static and kinetic friction. Explain the 2. Blocks…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: A 130-lb crate is being transported by a 175-lb hand- truck cart along the frictionless floor. The…

A: Initially both the crate and cart are at rest. When a load P is applied on the cart, there acts a…

Q: ▼ Part A-Power supplied to the crate when friction is considered Considering the coefficient of…

A:

Q: Q.2 Cylinder A is dropped from 2.4 m onto cylinder B, which is resting on a spring of constant k=300…

A:

Q: 15lb slender rod with length = 15m is released from rest (when vertical) and strikes the smooth…

A:

Q: PROBLEM 13.147 650 kg The 650-kg hammer of a drop-hammer pile driver falls from a height of 1.2 m…

A:

Q: Using a forked rod, a m=1.5 kg smooth ball bearing is confined to a path defined by the equation r-(…

A: Solution: Given Data: m=1.5 kgr=2.5θθ=πt28t=2 s

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.