63. 5.8. Two venturi meters are installed in a 30-cm-diameter duct that is insulated (Figure P5.8). The conditions are such that sonic flow exists at each throat (i.e., Mi = M4 = 1.0). Although each venturi is isentropic, the connecting duct has friction and hence losses exist between sections 2 and 3. pi = 3 bar abs. and p4 = 2.5 bar abs. If the diameter at section 1 is 15 cm and the fluid is air: (a) Compute As for the connecting duct. (b) Find the diameter at section 4. 19/1r ... ...

63. 5.8. Two venturi meters are installed in a 30-cm-diameter duct that is insulated (Figure P5.8). The conditions are such that sonic flow exists at each throat (i.e., Mi = M4 = 1.0). Although each venturi is isentropic, the connecting duct has friction and hence losses exist between sections 2 and 3. pi = 3 bar abs. and p4 = 2.5 bar abs. If the diameter at section 1 is 15 cm and the fluid is air: (a) Compute As for the connecting duct. (b) Find the diameter at section 4. 19/1r ... ...

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. Consider two tanks, A and B, each with a large opening at the top. The two tanks contain different liquids. A small hole is made in the side of each tank at the same depth h below the liquid surface, but the hole in tank A has three times the cross-sectional area of the hole in tank B. (a) If it is known that the mass flow rate is the same for the two holes, find the ratio of PALPB of the densities of the liquids in tanks A and B. (b) (c) equal volume flow rates, what height above the hole must the liquid in tank A be just then? Find the ratio RVAIRVB of the volume flow rates from the two tanks. At one instant, the liquid in tank B is 90 cm above the hole. If the tanks are to have
#2 fluid machineries. will upvote anyone who will answer, please make complete solution and corrects units. Thanks
2. The tapered cylindrical bar in Fig. 2 is subjected to opposing torques T on its free ends. For the tapered section only, the angle of twist 0 can be expressed as: 32 TI(d? + d,d2 + dž) Gd d? 37n (a) Derive an expression for the effective spring constant keff for the entire bar, treating each segment as a torsional spring in series. Fig. 2 (b) For the bar shown, let; I, = 12 = 12 in., 1= 24 in., d1= 0.25 in., d2= 1 in., T = 1000 lbf-in., and G = 13.5 x 103 kpsi. Calculate the angle twist 0 for the entire bar using the expression for kef determined in (a). Verify that this value is the sum the angles of twist for each individual %3D %3D segment.
Fluid Mechanic Water, as seen in the figure above, is a 25° angle contractor in a piping system. With an elbow, it is directed downward in the installation with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. The flow is frictionless and the effects of gravity are neglected. a-)Effective pressure at point 2 b-) Elbow in place Calculate the x and y components of the force required to hold and the resultant force (pwater =1000 kg/m3, g = 9.81 m/s2)
A small gap is left between a window and the windowsill, as shown in Figure P8.21. The gap is 0.15 mm by 30 mm, and the width of the window is 1 m. The pressure difference across the window is 60 P a. Estimate the average velocity and the volume flow rate through the gap. The air temperature is 0°C. Ignore minor losses.
10. A fluid moves in a steady flow manner between two sections in a flow line. At section 1:Ai-10ft, U1 = 100 fpm, vi = 4 ft'/lbm. At section 2: Az = 2 ft, p2 = 0.20lb/ft, Uz = 120 fpm. Calculate (a) the mass flow rate, and the (b) change of mass stored in system,Am. %3D %3D tbm Ans. (a.) m = 15,000 &m2 2880- (b.) 12 120 %3D %3D hr hr hr
a. Calculate the mass flow rate in lb/min. b. Calculate the speed at section 2 in ft/min or fpm
using: Step 1: Known, UnknownStep 2: SchematicStep 3: FormulaStep 4: CalculationsStep 5: Discussion find