6/101 For a certain coefficient of friction μl and a certain angle a, the force P required to raise m is 4 kN, and that required to lower m at a constant slow speed is 1.6 kN. Calculate the mass m. P a m Problem 6/101

Q: If the analysis of the forces involved on an object produces a negative answer for a force: The…

A: If doing calculation and getting any force hwith negative that means, The negative sign indicates…

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Fixing a wheel barrow takes a specific diameter axel of 2.50 inches. Thankfully, the manufacture…

A: It is given that the axle required for fixing the wheel barrow should have a diameter of 2.50…

Q: 8. A note in the comment section of a title block mentions that all faces should have a +.10…

A: Circularity (roundness) tolerance is 2-D in nature.

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: How do you solve parts a,b and c?

A:

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on both…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: Let me know if I have misinterpreted the question.

A: in this question all the help full values are given.In this question plate slider due to impact…

Q: I need answers for problems 7, 8, and 9 pertaining to the print provided.

A: As we are entitled to answer only a single question. We’ll answer question no. 7 for you. Please…

Q: There are several failure modes by which gears can fail. Select the true statement from among the…

A:

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: Replace the loading by an equivalent resultant force. Suppose that w₁ = 2 kN/m and w₂ = 5.5 kN/m.…

A:

Q: Please answer part c and e onwards with working out and answer and please label the parts as you…

A: c) TDC=Top Dead Center BDC=Bottom Dead Center Stages Ideal cycle Actual cycle Stage 1 It is…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.